Gemini CFX-50 Manual Del Operador página 5

INTRODUCTION:
Congratulations on purchasing a Gemini CFX-50 Dual CD Player.
This state of the art professional CD player is backed by a three year
warranty, excluding lasers. One year warranty on CD lasers. Prior to
use, we suggest that you carefully read all the instructions.
FEATURES:
• 5 Hot Cue Points & BOP Feature
• Real Time Scratching
• Auto BPM Within LCD Display
• Fully Adjustable Brake & Start
• Variable Pitch Control (4%, 12%, 24%, & 100%)
• 5 DSP Effects With Time & Ratio Parameter Control
• New "State of the Art" Master Tempo With, Fully Functional Pitch
• Large LCD Screen with Blue LED Backlight & Dimmer Control
• Direct Access Keypad with Full Programmable Feature
SAFETY CERTIFICATIONS
Laser Diode Properties
Material: Ga - Al - As
Wavelength: 755 - 815 nm (25° C)
Laser Output: Continuous Wave, max. 0.5mW
CAUTIONS:
Do not use this CD Player at temperatures below 41°F/5°C or higher
than 95°F/35°C. The apparatus should not be exposed to dripping or
splashing and no objects filled with liquids such as vases should be
placed on the apparatus. Place the unit in a clean and dry location.
Do not place the unit in an unstable location. When disconnecting the
power cord from an AC outlet, always grasp it by the plug. Never pull
the power cord. To prevent electric shock, do not remove the cover or
the bottom screws. There are no user serviceable parts inside. Please
refer servicing to a qualified technician. Do not use chemical solvents to
clean the unit. Keep the laser pickup clean by keeping the drawer
closed. Keep this manual in a safe place for future reference.
IMPORTANT NOTE:
Since the CFX-50 is a dual CD player, most of the functions and controls
are duplicated on both sides of the CD player. To eliminate confusion and
to make the drawings easier to understand, we will only number the
left side functions and controls.
LINE VOLTAGE SELECTION:
Model CFX-50 is a dual voltage unit. It will operate at 115 or 230 volts.
To set the proper voltage, follow these steps:
1. Place the head of a screwdriver in the center of the VOLTAGE
SELECTOR SWITCH (1) found on the rear panel.
2. Slide the switch to 115 or 230 volts.
3. Do not force or twist the switch. Excessive force may cause damage. If
the switch does not move smoothly, contact a qualified technician.
CONNECTIONS:
1. Connect the power plug into the AC IN (2) for POWER.
2. Using the included cables, plug one end into the REMOTE CONTROL (3)
connector on side 2 and the other end into the MAIN UNIT (3) connector
also on side 2. Do the same for side 1.
3. Plug one end of a set of the included RCA cable connectors into each of
the LINE OUTPUT JACKS (4).
4. Plug the other end of the RCA connectors into any available line level
input jacks on your mixer. If you are connecting the CFX-50 through a
receiver, you can plug the RCA connectors into the CD or AUX INPUT
JACKS on your receiver. If there are no CD or AUX INPUTS, use any
line level (not phono) inputs.
5. Connect any type of device that will accept a DIGITAL signal, such as
DAT, MD, HARD DRIVE, ETC to the COAXIAL (5) INPUTS on the rear
panel of the transport to record a DIGITAL signal.
• Seamless Looping & Instant Reverse
• Anti-Shock Using RAM Buffer Memory
• Large Soft Touch Rubber Jog Wheel
• LED Target Light for Draw Mechanism
FUNCTION DESCRIPTIONS:
ANTI-SHOCK BUFFER MEMORY: With 12 SECONDS OF ANTI-
SHOCK BUFFER MEMORY, each side of the CD player stores 6
seconds of future play to ensure that any harsh movement or bumping of
the unit will not interrupt play and play will continue smoothly.
NOTE: REFER TO CONNECTION SECTION FOR REMOTE CONTROL (3) & LINE OUTPUT JACKS (4).
POWER: After making sure that the VOLTAGE SELECTOR (1) switch,
found on the rear panel, is properly set, plug the unit in and press the
POWER (6) button. The unit will turn on. Pushing the POWER button
(6) a second time will turn the unit off.
DISC TRAY: The DISC TRAY (7) is where the CD is held during loading,
unloading and playback. Pressing the disc trays STOP (8) button, will
open or close the tray. The DISC TRAY (7) holds both 12 cm and 8 cm
CDs. Please note, if the CFX-50 is in play mode, the tray will not open.
NOTE: DO NOT FORCE THE DISC TRAY (7), EXCESSIVE FORCE MAY DAMAGE THE CD MECHANISM.
STOP: Press the STOP (8) button to STOP a CD in PLAY mode and to
also load or remove a CD from the DISC TRAY (7).
NOTE: THE STOP (8) BUTTON ONLY FUNCTIONS AS STOP AND EJECT ON THE REMOTE CONTROL.
DIMMER: Turn the DIMMER (9) to the right to increase brightness of the
DISPLAY (10), and push it in to lock the setting.
DISPLAY: The DISPLAY (10) shows the track number, pitch value, single-
auto cue, continue (for continuous play), and 3 different time displays.
These time displays are time elapsed on the track, time remaining on the
disc and time remaining on the track. Time is measured in minutes,
seconds and frames. It also shows the beats-per-minute of the track.
PLAYBACK DISPLAY BAR: The PLAYBACK DISPLAY BAR (11)
displays the elapsed and remaining time for each track. The display
flashes slowly when the track has 15 seconds remaining and pulses
rapidly when playing time is down to 5 seconds.
PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (12) causes
the operation to change from play to pause or from pause back to play.
CUE/PREVIEW: With the unit in the PLAY mode and after the CUE POINT
has been programmed, pressing CUE/PREVIEW (13) will cause the CD
player to enter the PAUSE mode at the programmed CUE POINT. Holding
down the CUE/PREVIEW (13) button changes the function to PREVIEW
and starts the CD from the programmed CUE POINT. Releasing the CUE/
PREVIEW (13) button will return the CD laser to the preset CUE POINT.
TRACK : The TRACK (14) buttons let you select the track to play.
SEARCH : The SEARCH (15) buttons are used to move forward
or reverse while in play or pause mode. See the CUE INSTRUCTIONS
section for more information.
TIME: The TIME BUTTON (16) switches the time display between the
three available choices listed under DISPLAY (10).
SINGLE: Pressing the SINGLE (17) activates the AUTO CUE FUNCTION.
The AUTO CUE FUNCTION causes the unit to pause at the beginning of
music of the following track and allows you to start play immediately
from the start of music without any blank space (which exists at the
beginning of every track). Pressing the SINGLE (17) button a second
time activates the CONTINUOUS function causing the unit to play
continuously (after the last track, the unit will return to the first track of
the disc and continue to play). Pressing the SINGLE (17) button a third
time deactivates the CONTINUOUS function.
FLY CUE: The FLY CUE (18) function lets you set cues "on the fly" with the
press of a button. Press FLY CUE (18) when the disc reaches the musical
location you wish to make your cue or start point. The CUE POINT is now
programmed. Press CUE/PREVIEW (13) to return to the CUE POINT. Press
PLAY/PAUSE (12) and the unit start from the pre-programmed spot.
(5)