Publicidad
Idiomas disponibles
Idiomas disponibles
Tool Specifications
Planer
Order Number
Power [W]
Frequency [Hz]
Amperage
127V [A]
220V [A]
-1
No-load speed [min
]
Maximum planning depth [mm]
Maximum rabbeting width [mm]
Maximum rabbetting depth [mm]
Weight without cable, approx. [Kg]
Protection class
Machine Elements
A
Storage for key & spare knives
B
Securing bolt
C
Cutter block screws
D
Knob for setting planing depth
E
Planing depth indicator
F
Dust port
G
Safety support
H
Auxiliary handle
I
Wing nut for adjusting handle
J
Safety switch
K
On/off switch
L
Rabbeting depth adjuster *
M
Rip fence*
N
Wrench*
O
Wrench Storage *
* Not all of the accessories illustrated or described are
included as standard delivery.
Introduction
This tool is intended for planing wooden materials such as
beams and boards, it is also suitable for chamfering edges
and rabbeting.
This machine is restricted to the domestic use, no being
indicated for professional works.
Read and save this instruction manual
Noise/vibration information
Measured values determined according to EN 50 144.
Typically the A-weighted noise levels of the tool are: Sound
pressure level: 85 dB (A).
Sound power level: 96 dB (A).
Wear ear protection!
The typical weighted acceleration is 3,5 m/s
Safety
WARNING! Read all instructions Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term "power tool" in all of
the warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless)
power tool.
SAVE THESE INSTRUCTIONS
1. Work area
a) Keep work area clean and well lit. Cluttered and poorly
lit areas can result in accidents.
b) Do not operate power tools in the presence of
flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
1555
F 012 1555..
550
50 / 60
4,5
2,5
16.000
1,5
82
8
3,0
E
/ II
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not misuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while if you are tired or under the
influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the
off-position before plugging in. Carrying power tools
2
with your finger on the switch or plugging in power tools
that are switches on invite accidents.
d) Remove any adjusting key or wrench before
switching on the power tool. A wrench or a key left
attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust-related hazards.
10
Publicidad
