Conformity And Approval; Safety Notes - Monacor IWA-05BT/WS Manual De Instrucciones

IWA- 05 BT/ WS
Order No. 17.9000
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
In-Wall Bluetooth Amplifier
These instructions are intended for experts
(installation) and for all users (operation).
Please read the instructions carefully prior
to installation and operation and keep
them for later reference.
1 Applications
This amplifier is designed for in-wall installa-
tion. With its small size, it fits into standard
wall boxes (e. g. for light switches). It delivers
an RMS power of 2 × 2.5 W at 8 Ω speakers
and is suited for stereophonic or monophonic
operation. There are two options to connect an
audio source: Either use the wireless Bluetooth
technology (e. g. from a smartphone or tablet
computer) or use the 3.5 mm jack for analog
connection. It is also possible to define the gain
and thus the maximum possible volume.

1.1 Conformity and approval

Herewith, MONACOR INTERNATIONAL declare
that the amplifier IWA-05BT/ WS complies with
the directive 2014 / 53/ EU. The EU declaration
of conformity is available on the Internet:
www.monacor.com
The amplifier operates in the 2.4 GHz range
and is generally approved for operation in
EU and EFTA countries. It is licence-free and
requires no registration.

2 Safety Notes

The units (amplifier and power supply unit) cor-
respond to all relevant directives of the EU and
are therefore marked with
WARNING The power supply unit uses
dangerous
Leave servicing to skilled per-
sonnel only. Inexpert handling
may result in electric shock.
•
The units are suitable for indoor use only.
Protect them against dripping water, splash
water and high air humidity. The admissible
ambient temperature range is 0 – 40 °C.
•
Do not operate the units and immediately
disconnect them from the power supply
1. if one of the units is visibly damaged,
2. if a defect might have occurred after a unit
was dropped or suffered a similar accident,
3. if malfunctions occur.
In any case, the units must be repaired by
skilled personnel.
•
For cleaning only use a dry, soft cloth; never
use water or chemicals.
•
No guarantee claims for the units and no li-
ability for any resulting personal damage or
material damage will be accepted if the units
are used for other purposes than originally
intended, if they are not correctly connected,
or if they are not repaired in an expert way.
ELECTRONICS FOR SPECIALISTS
If the units are to be put out of oper-
ation definitively, take them to a local
recycling plant for a disposal which is not
harmful to the environment.
3 Installation
There is a risk of electric shock when the
power supply unit is connected to the mains
voltage. Therefore, installation must always
be carried out by experts!
1) Connect the speakers to the terminal pairs
R+/ R− (2) and L+/ L− (3). The impedance of
a speaker or the total impedance of a group
of speakers must not fall below 8 Ω at any
terminal pair.
2) Connect the output of the power supply
unit (7) to the power supply input (6) of the
amplifier:
red core ➾ terminal V+
black core ➾ terminal GND
.
mains voltage.
ELECTRONICS FOR SPECIALISTS
+
−
L + L R + R
1
2 3
4 4
R + R L + L
5
V+ GND
4 4
6
V+ GND
7
ELECTRONICS FOR SPECIALISTS ELECTRONICS
3) Use the lower jumper (5) to select the oper-
ating mode:
mono
4) If required, use the upper jumper (5) to
change the gain and thus the maximum
possible volume:
5) Connect the mains cable (8) of the power sup-
ply unit to the mains (100 – 240 V/ 50 – 60 Hz).
6) The amplifier fits into standard wall boxes.
Depending on the depth of the wall box,
install the power supply unit in the same box
or use a separate box. Attach the mounting
frame of the amplifier to the wall or to the
wall box by means of the holes (1).
7) Put the cover plate on the amplifier. The lugs
of the cover plate will engage in the holes (4)
of the mounting frame.
L N
100-240 V ˜
INPUT
50-60 Hz
POWER SUPPLY
BLACK RED
GND V+
OUTPUT 15V /12 W
stereo
maximum gain
average gain
minimum gain
8