Monacor IWA-05BT/WS Manual De Instrucciones página 4

IWA- 05 BT/ WS
Order No. 17.9000
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
4 Operation
4.1 Bluetooth audio source
The amplifier IWA-05BT/ WS is able to receive
audio signals via Bluetooth (e. g. from a smart-
phone or tablet PC) if these devices support the
Bluetooth profiles A2DP/AVRCP. The reception
range is 10 m. Each amplifier is provided with
a 4-digit Bluetooth ID number (9) which will
make it possible to distinguish between sever-
al amplifiers when more than one amplifier is
used in the same area.
1) Activate the Bluetooth function at the Blue-
tooth audio source ( ☞ manual of the Blue-
tooth audio source).
2) Keep the button (11) pressed for 4 sec-
onds: The amplifier is switched on and the
LED (12) starts flashing in blue.
3) As long as the LED keeps flashing, select the
amplifier from the list of available Bluetooth
devices at the Bluetooth audio source and
pair* the amplifier. The amplifier will be
listed as KINGBT-XXXX [XXXX representing
the number (9) of the amplifier]. When the
devices have been paired, they will be con-
nected automatically. When the connection
has been established, the LED will light per-
manently.
If the Bluetooth connection has not been
established after one minute, the amplifier
will be switched off.
*Note: If this is not the first time that the two devices
are connected, pairing will be omitted and the
connection will be established immediately.
4) Start the audio replay at the Bluetooth audio
source.
5) Set the volume at the Bluetooth audio
source.
6) When the Bluetooth connection is discon-
nected on the part of the Bluetooth audio
source, the LED starts flashing and the am-
plifier is ready to be connected once again.
If the connection has not been re-estab-
lished after one minute, the amplifier will be
switched off.
7) To switch off the amplifier manually, keep
the button pressed until the LED goes out.
ELECTRONICS FOR SPECIALISTS
4.2 Analog audio source
1) Use a cable with 3.5 mm plug to connect an
analog audio source (e. g. the line level out-
put or headphone output of a mobile audio
unit, computer or mixer) to the jack AUDIO
IN (10). When the plug has been connect-
ed, the amplifier is switched on and the LED
(12) lights up in red. If there is a Bluetooth
connection, this connection will be discon-
nected.
2) Set the volume at the audio source.
3) To switch off the amplifier, disconnect the
3.5 mm plug. The LED will go out. When the
plug has been disconnected, the Bluetooth
mode will not be resumed automatically.
The Bluetooth audio source must be recon-
nected for replay via the amplifier.
Specifications
RMS power
at 8 Ω
at 16 Ω
Frequency range
Channel separation
THD
S/N ratio
Power supply
Power consumption
Standby
Operation
Bluetooth specifications
Profiles
Transmission frequency band
Transmission power
Range
Analog input
Rated level
Connection
Dimensions (W × H × D)
Amplifier with cover plate
Installation dimensions of the amplifier
Power supply unit
Weight
Ambient temperature
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS
IWA-05BT/WS
9
XXXX
10 11
PAIRING

4 s
AUDIO IN
2 × 2.5 W
2 × 1.5 W
45 – 20 000 Hz
≥ 58 dB
≤ 0.1 %
≥ 84 dB
⎓ 15 V via power supply unit provided
and connected to 100 – 240 V/50 – 60 Hz
≈ 0.6 W
15 VA max.
class 2, BT2.1 + EDR
A2DP 1.2, AVRCP 1.4
2.4 GHz
7 dBm
10 m
100 mV
stereo jack, 3.5 mm
80 mm × 80 mm × 41 mm
45 mm × 45 mm × 36 mm
49 mm × 51 mm × 26 mm
74 g
0 – 40 °C
Subject to technical modification.
A-1940.99.03.04.2019
12