Cleaning And Usage Of The Icemaker; Door Alignment; Cleaning The Ice Cube Tray; Icemaker Usage Precautions - Haier HB26FSSAAA Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 126

Cleaning and usage of the icemaker

Door Alignment

If the two door of the refrigerator compartment are not level, please
adjust the door height as follows.
1. Lift the lowest door at the hinge side.
2. Using a pair of pliers inset a 'C' washer in the hinge as shown.
The 'C' washer should be next to the hinge bracket.
3. Insert as many 'C' washers as required to lift the door to match
the other door height. A total of 3 'C' washers are provided in the
accessory bag.
1.
2. Remove the icemaker assembly from the refrigerator and
turn over the icemaker, so that the ice cube tray is visible.
3. Pull the oval shaped fastener on the ice tray in the direction
of arrow 1.
Tilt the ice tray upward and pull it out in the direction of
arrow 2.
4. After cleaning the tray, put it back in, then
the icemaker, close the freezer drawer, and switch on the
icemaker function via the display panel.

Icemaker usage precautions

Caution
For newly installed appliance, you should wait for 24 hours.
This will enable the freezer compartment to cool down, so that
it can make ice.
• The ice machine will make 8 ice cubes each time; but the
ice-making quantity will depend on the indoor
temperature, frequency that the doors are opened, water
pressure, freezer compartment temperature, etc.
• In order to ensure that the ice tray gets
cubes, the ice tray should be frequently pulled out so that the
ice cubes get evenly distributed.
• It is a normal phenomenon that some of the ice cubes will
clump together during removing.
• When the freezer compartment reaches or is below -12 °C,
the icemaker will start making ice (if you are just beginning to
use the icemaker, or it has not been used to make ice in a
long time, you should discard the first several ice cubes, so
that impurities in the water line get run out.)
• The icemaker must be installed in the refrigerator through an
authorized service agency.
Cleaning the
ice cube tray
1. Turn off the icemaker
function via the display
panel, hold down the
handle of the
icemaker, and use
strength to pull out the
icemaker.
push in
up with ice
The icemaker can only be supplied with water via the
container on top of the left door unit. It can not be
connected directly to an external drinking water supply.
If you occasionally hear unusual sounds in
the refrigerator
You may occasionally hear some "crunching" sounds, but
these are just normal sounds that are emitted during ice
making, so do not worry.
If you do not often use ice cubes
"Old" ice cubes will become cloudy, and will not taste fresh;
therefore, please periodically clean the ice cube tray and
wash it out with warm water. Before replacing the ice cube
tray, be sure to cool it down, otherwise, ice will stick to other
parts of the ice machine and affect the ice making function.
If the icemaker in the freezer compartment
is not used for a long time
If not used for a long time, please remove the automatic
icemaker and any residual ice cubes in the ice storage
compartment, wash the ice cube tray and the ice storage
compartment with warm water, wipe them dry with a clean
towel and put them somewhere else in order to increase
storage space.
The water reservoir should be removed, any residual
water should be drained out .
Throw out the first few batches of ice cubes if you are
making ice for the first time or have not made it for a long
time.
If the cubed ice becomes smaller, this may suggest that the
filter is blocked from the impurities.
22

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Hb26fgsaaaHb26fsnaaa

Tabla de contenido