Stiga Silex 75-G Instrucciones De Uso página 43

Ocultar thumbs Ver también para Silex 75-G:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 72
3.5 Cable for reverse control
Only applies to 75R.
The cable is marked R.
1. Pull the cable up under the cover (1:G) and over
the handle's screws.
2. Hook the cable in the reverse control (1:A) and
insert the cable in the gap in the cable housing's
mounting on the left handle.
3. Adjust the cable sleeve if necessary.
3.6 Drive cable
1. Pull the cable up under the cover (1:G) and over
the handle's screws.
2. Hook the cable in the drive control (1:B) and in-
sert the cable in the gap in the cable housing's
mounting on the left handle.
3. Adjust the cable sleeve if necessary.
3.7 Splash guards
Install the splash guards on the right and left sides.
Use the screws, nuts and washers supplied.
3.8 Rotor
Install the outer rotors and cutting discs (1:O). Use
the screws, nuts, locking pins and washers sup-
plied. See fig. 8.
4 DESCRIPTION
The rotary cultivator is driven by a four-stroke en-
gine and is intended for soil cultivation in private
gardens. The most important parts and controls of
the rotary cultivator are described below.
4.1 Reverse control (1:A)
Only applies to 75R.
The control is used to start the rotor for reverse
when the engine is running.
The reverse control and drive control (1:B) must
never be activated at the same time.
Control in idle mode (forward) – No drive.
Control moved backwards – The machine
reverses.
4.2 Drive control (1:B)
The control is used to start the rotor for forward
motion when the engine is running.
The reverse control (1:A) and drive control must
never be activated at the same time.
Control in idle mode (down) – No drive.
Control pulled in – Forward operation.
ENGLISH
4.3 Throttle and stop (1:C)
The control determines the engine's rpm and has
start and stop positions.
The throttle control determines the speed and is
used to stop the engine.
Stop: Control in the rear position.
Idle: Control 1 cm in front of rear position.
Full throttle and start: Control in the front position.
4.4 Handle (1:D)
The handle has two handgrips that are used to op-
erate the machine over the area to be cultivated.
4.5 Fuel cap
Unscrew the fuel cap to fill with petrol. The fuel
cap must always be closed during operation.
The fuel cap is shown according to the table below:
Machine
75-G
75R-B
75R-H
75R-HX
4.6 Protective grille (1:F)
The protective grille must always be installed dur-
ing operation. There are surfaces that become ex-
tremely hot under the protective grille that risk
causing personal injury if touched.
4.7 Cover (1:G)
The cover protects cables and the handle adjust-
ment.
4.8 Adjusting handle (1:H)
Slacken off the screws and set the handle to a com-
fortable working position.
Then retighten the screws again.
4.9 Oil filling
Always check the oil level before start-
ing the engine.
Plug for oil filler and checking the oil level.
The plug is shown according to the table below:
Machine
75-G
75R-B
75R-H
75R-HX
GB
Figure:Position
2:E
1:E
3:E
4:E
Figure:Position
2:J
1:J
3:J
4:J
43

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Silex 75r-bSilex 75r-hSilex 75r-hx

Tabla de contenido