Changing The Oil - Stiga Silex 75-G Instrucciones De Uso

Ocultar thumbs Ver también para Silex 75-G:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 72

7.4 Changing the oil

Change the oil the first time after 2 hours of oper-
ation, and subsequently every 25 hours of opera-
tion or at least once a season. Change oil when the
engine is warm.
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. So allow the engine to cool a few
minutes before draining the oil.
1. Lean the machine slightly so that the oil drain-
ing plug is the lowest point of the engine.
2. Unscrew the oil draining plug. See "4.10".
3. Let the oil run out into a container.
4. Screw back the oil draining plug.
5. Fill with new oil: See "5.2".
7.5 Side adjustment
If the handle's side adjustment (1:P) does not lock
the handle satisfactorily it can be adjusted as fol-
lows:
1. Remove the handle's support by carrying out
the procedure in "3.2" reverse order.
2. Adjust the lock on the nut in fig. 7.
Tightening secures the lock better.
Slackening off makes the lock less secure.
3. Reinstall the handle according to the procedure
in "3.3".
7.6 Cleaning
Never use high-pressure washing equip-
ment when cleaning. This can cause wa-
ter to penetrate between the seals and
cause machine damage.
First brush off all dirt. Then wipe down the rotary
cultivator using a damp cloth. The underside can
be washed with water.
7.7 Fault-tracing
Fault: Difficult to start
Cause: The fuel is too old.
Action: Drain the tank and fill with fresh petrol.
Cause: Sparkplug fault.
Action: Replace spark plug.
Fault: Engine runs unevenly
Cause: Contaminated fuel.
Action: Clean the petrol tank and carburettor.
Cause: Sparkplug fault.
Action: Replace spark plug.
Fault: Weak engine, does not run at full throttle
Cause: Blocked air filter
Corrective action: Clean or replace the air filter.
ENGLISH
Fault: Stops during operation
Cause: No fuel.
Action: Fill with petrol
Authorised service stations carry out repairs and
servicing. They always use genuine spare parts.
Under no circumstances may parts oth-
er than genuine spare parts be used.
This is a requirement stipulated by the
Testing Authority. The machine is ap-
proved and tested with these parts.
If the machine requires servicing, repair
or maintenance that entails dismantling
of the cover, this must be performed by
an authorised service station.
The manufacturer reserves the right to make alter-
ations to the product without prior notification.
9 PURCHASE TERMS
A full warranty is issued against manufacturing
and material defects. The user must carefully fol-
low the instructions given in the enclosed docu-
mentation.
Warranty period
According to relevant laws.
Exceptions
The warranty does not cover damage due to:
- Neglect by users to acquaint themselves with
accompanying documentation
- Carelessness
- Incorrect and non-permitted use or assembly
- The use of non-genuine spare parts
- The use of accessories not supplied or approved
Neither does the warranty cover:
- Wear parts
- Normal wear
The purchaser is covered the national laws of each
country. The rights to which the purchaser is enti-
tled with the support of these laws are not restrict-
ed by this warranty.
GGP reserves the right to make alterations to the
product without prior notification.
GB
8 SERVICE
47

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Silex 75r-bSilex 75r-hSilex 75r-hx

Tabla de contenido