Work Instructions; Environmental Protection - Narex EPL 12-7 BE Instrucciones De Uso

Pokyny pro práci
Pozor! Nebezpečí poranění. Obrobek upevněte vždy tak,
aby se nemohl při práci pohybovat!
Používejte ostré pilové listy, které jsou určené pro daný materiál. Počet
zdvihů a předkmit přizpůsobte materiálu. Při řezání kovu potřete místo
řezu vhodným mazacím prostředkem, aby se tak zabránilo přehřívání
pilového plátku.
Dbejte na rovnoměrnost posuvu listové pily do řezu.
Po vypnutí listové pily pilový plátek (3) nebrzděte natáčením pily
do stran!
Volné vedení pily podle nárysu
Trojúhelníkovitý trn na vložce proti třepení materiálu (6) ukazuje linku
vedení pilového listu (3). Tím je usnadněné vedení stroje podle nárysu.
Zanoření pily bez předvrtání
Pro zanoření pilového listu do dřevěných materiálů musí být saně listové
pily (7) v přední poloze (viz kapitola Natavení řezných parametrů).
‰ Položte listovou pilu přední hranou saní listové pily na materiál,
do kterého budete zanořovat pilový list.
‰ Při plných otáčkách a nastaveném předkmitu na maximální hod-
notu (poloha 3) zvolna zanořte pilový list do materiálu.
Pozor! Postupujte se zvýšenou opatrností, protože může dojít
k ohnutí pilového listu a k jeho následnému zlomení, čímž může
dojít k jeho odlétnutí a může tak způsobit zranění!

Work Instructions

Attention! Risk of injury. Secure the workpiece to avoid its
movement while being machined!
Use sharp saw blades intended for the relevant material. Adapt the
number of strokes and the pendulum stroke to the material. When cut-
ting metal, coat the cut zone by a suitable lubricant to avoid saw blade
overheating.
Take care of uniform saw blade movement to the cut.
When the jig saw is switched off, do not brake the saw blade (3) by swiv-
elling the jig saw to the sides!
Free jig saw guide by the scribe mark
The triangular pin on the splinter guard (6) shows the saw blade (3)
guide line. Guiding the jig saw by the scribe mark is thus facilitated.
Jig saw cutting without pre-drilling
For plunge cuts in timber materials the jig saw base runner (7) must be
in the front position (see the chapter Cut Parameter Setting).
‰ Place the jig saw by the front base runner edge on the material,
where the saw blade will be plunged into.
‰ Plunge the saw blade slowly into the material at full speed and pen-
dulum stroke preset to the max. value (position 3).
Attention! Proceed carefully, because the saw blade can be bent
and/or broken and fly off, thus causing serious injury!
Accessories
Guide for straight cuts/parallel guide (27)
(Optional accessories)
Use the parallel guide to guide the jig saw parallel to the workpiece
edge. The parallel guide can be fitted on any side of the jig saw base
runner (7).
‰ Slide the clamping clip (29) onto the base runner from the front.
‰ Insert the parallel guide (27) from the requested side into the
clamping clip hole and set the requested position which shall be
measured from the saw blade to the parallel guide stop (30).
‰ Tighten both locking screws (31) of the clamping clip.
Attention! Prior to mounting the parallel guide, the chip guard (10)
must fixed, if it shall be used!
Guide for circular cuts (circle cutter) (28)
(Optional accessories)
The circle cutter can be used to produce circular cuts with the diameter
ranging from 120 to 720 mm. The circle cutter can be fitted on any side
of the jig saw base runner (7).
‰ Slide the clamping clip(29) onto the base runner from the front.
‰ Insert the circle cutter (28) from the requested side into the clamp-
ing clip hole and set the requested position which shall be meas-
ured from the saw blade to the centre of the rear hole for the circle
cutter pin (32).
‰ Tighten both locking screws (31) of the clamping clip.
‰ Insert the circle cutter pin (33) into the rear circle cutter hole.
Steel base runner pad
The manufacturer inserts the plastic base runner pad (8) on the jig-saw
base runner. The pad slides smoothly on the wooden and plastic materi-
als, thus restricting occurrence of scratches on the cut material.
The steel base runner pad (34) is suitable for use on all other materials.
‰ To replace the base runner pad, it is necessary to unscrew six screws
on the bottom side of the jig saw base runner (7).
‰ Take out the base runner pad (8) and replace it for the requested
one.
‰ Screw all six screws on the bottom side of the jig saw base runner
and tighten carefully.
Maintenance and service
Attention! Risk of el. shock. Prior to start any operation,
pull the plug out of the socket!
Jig saw vent holes (35) may not be clogged. Clean them regularly, pref-
erably by compressed air. When cutting conductive material, the jig saw
must be cleaned carefully. Blow the vent holes by the compressed air in
the rear jig saw part where the motor is mounted.
Lubricate the rod (21) and the guide bell (20) by a few drops of oil from
time to time.
Attention! With respect to protection from el. shock and
preservation of the class of protection, all maintenance
and service operations requesting jig saw case removal
must be performed by the authorized service centre only!
The current list of authorized service centres can be found at our
website www.narex.cz, section "Service Centres".
Packed appliance may be stored in dry, unheated storage place with
temperature not lower than -5 °C.
Unpacked appliance should be stored only in dry storage place with
temperature not lower than +5 °C with exclusion of all sudden tempera-
ture changes.

Environmental protection

Power tools, accessories and packaging should be sorted for environ-
mental-friendly recy.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electrical and
electronic equipment and its incorporation into national law, power
tools that are no longer suitable for must be separately collected and
sent for recovery in an environmental-friendly manner.
English
Storage
21