Precautionary Measures; Transport; Packaging; Inspection On Receipt - Rancilio CLASSE 10 USB Instrucciones Originales

The user must not:
 touch the hot surfaces and dispensing areas;
 place liquids containers on the machine;
 put his hands under the spouts during use;
 transport the machine or carry out maintenance
operations when the plug is connected or when
the machine is hot;
 wash the machine with water or steam jet;
dip completely or partially the machine in water;

 use the machine if the cable is damaged;
 touch the machine when his hands or feet are wet
or damp;
 use the machine when there are children in its
proximity;
 allow the machine to be used by children or unfit
people;
 obstruct the suction or dispersal grilles with cloth
or any other thing;
 do not use the machine when wet or very damp.

4.1. Precautionary measures

This machine may only be used with foodstuffs. It
cannot be used for heating liquids or grinding any
other kind of product that could damage and pollute it.
The manufacturer cannot be held responsible
for damage to people or things caused by
unsuitable, erroneous or irrational use.

5. TRANSPORT

5.1. Packaging

The machine is delivered in a strong cardboard box
with internal protection.
The packaging bears symbols which must be obser-
ved during handling and stocking of the item.
Always keep the package in a vertical position
during transport. Do not turn it over or lay it
on its side and avoid bumping and exposure
to atmospheric agents.

5.2. Inspection on receipt

Check that the machine received corresponds to
the one indicated on the delivery note, including any
accessories.
Check that it has not been damaged during transport
and, if so, inform the forwarder and our customer
service office immediately.
The packing elements (plastic bags, expan-
ded polystyrene, nails, cardboard, etc.) must
not be left within reach of children as they are
potential sources of danger. Do not dispose
of the packing elements in the environment;
consign them to firms authorized for their
disposal.
70

6. INSTALLATION

The appliance is only to be installed in
locations where use and maintenance is
restricted to trained personnel.
The machines are fitted with height adjustable feet.
The support surface shall be levelled, dry, smooth,
steady and stable and at such a height that the cup-
warming surface is at over 150 cm from ground. Do not
use water jets or install where water jets are used.
In order to guarantee normal operation, the machine
must be installed in areas that the environmental
temperature is between +5°C ÷ +32°C end humidity
of not over 70%.
It does not need to be anchored to the surface and it
does not require any technical operations to dampen
vibrations in order to operate properly.
It is recommended to leave the area around the ma-
chine free to facilitate its use and the performance
of any maintenance operations.
If the machine is wet or very damp, wait until it is
completely dry before installing or using it. It is always
necessary to request an accurate control to qualified
service people in order to find any possible damage
to the electric components.
Reserve an area near the machine for the installa-
tion of the coffee grinding and dosage machine (see
relevant documentation).
The machine is usually equipped with a water sof-
tener, type DP2 or DP4, which must be connected
by the user in compliance with the laws in force.
Should a different softener be installed, refer to the
documentation of the relevant product.
A dreg drawer should be fitted by the installer.
6.1. Connections to be made by the
user
Hook-up must be carried out by qualified
personnel in full accordance with federal,
state and local regulations.
6.1.1. Water and gas supply (Fig.6)
This equipment is to be installed to
comply with the applicable federal,
state or local plumbing codes.
Make sure that the maximum supply pressure
does not exceed 6.5 bar; otherwise, install a
pressure reducer.
Connections must be installed close to the machine.
1) Water drainage pipe 1, having a minimum internal
diameter of 30 mm, equipped with a water-trap
accessible for inspection.
2) Water supply pipe 2, with a 3/8"G cut-off tap.
Water supplies to the machine must be suitable for
consumption by man and for human uses, in com-
pliance with all the laws in force in the installation site.
The installation technician is required to get confirma-
tion from the final owner and/or user of the system