TFA Dostmann 30.3006 Manual De Instrucciones página 28

•
Within ferro-concrete rooms (basements, superstructures), the received
signal is naturally weakened. In extreme cases, please place the unit close to
a window and/ or point its front or back towards the Frankfurt transmitter.
•
During nighttime, the atmospheric disturbances are usually less severe - the
reception is possible in most cases. A single daily reception is adequate to
keep the accuracy deviation below 1 second.
MANUAL CLOCK SETTING:
Hours (flashing)
In case the Temperature Station may not be able to detect the DCF-signal
(disturbances, transmitting distance, etc.), the time can be manually set. The clock
will then work as a normal Quartz clock:
1. Press and hold down the SET key for around 3 seconds until the time display
flashes.
2. Use the IN key to set the hours and the OUT key to set the minutes. Pressing
these keys continuously moves the hours consecutively by 1 and the minutes
consecutively by 5.
3. Either press the SET key once more to enter the set mode for the time zone
and date section or do not touch any buttons for around 30 seconds to
confirm the set time.
Note:
The unit will still try to receive the signal every hour despite it being manually set.
When it does receive the signal, it will change the manually set time into the
received time. During reception attempts the DCF tower icon will flash. If reception
has been unsuccessful, then the DCF tower icon will not appear but reception will
still be attempted the following hour.
LCD 2 TIME ZONE AND DATE SETTING:
The second section of the LCD shows either the date and month, the weekday and
date, Alarm ((1)) time or Alarm ((2)) time. It also shows the Alarm ON/OFF icons
((1)) and ((2)).
TIME ZONE SETTING:
Time Zone (flashing)
The time zone default of the Temperature Station is 0. To re-set the time zone:
1. Press the SET key after completing the time setting in order to enter the time
zone setting (flashing).
2. Using the IN key, set the time zone. The range runs from 0 to +9 and then
runs from -9 back to 0 in consecutive 1hour intervals.
3. Press the SET key to enter the date setting mode or do not touch any buttons
for around 30 seconds to confirm the time zone setting.
DATE SETTING:
Minutes (flashing)
Year (flashing)
The date default of the Temperature Station is 1. 1. or TH 1. in the year 1998. Once
the radio-controlled time signals are received, the date is automatically updated.
However, if the signals are not received, you can adjust the date manually.
To do this:
1. Press the SET key after completing the time zone setting in order to enter the
year setting (flashing). Reset the year by pressing the IN key. The range runs
from 1998 to 2020.
2. Press the SET key again to enter the month and date display (flashing).
3. Using the OUT key, set the month required. Using the IN key, set the date
required.
4. Press the SET key again to enter the weekday display (flashing).
5. Using the IN key, set the weekday required.
6. Press the set key once more to confirm all settings or do not touch any
buttons for around 30 seconds. The mode will return to normal.
ALARM SETTING:
1. Press and hold down the AL1 key for around 3 seconds until the alarm time
display flashes.
2. Use the IN key to set the hour and the OUT key to set the minutes. Pressing
these keys continuously moves the hours consecutively by 1 and the minutes
consecutively by 5.
3. Either press the AL1 key once more to confirm and return to the normal
display or do not touch any buttons for around 30 seconds to confirm the set
time.
4. To activate the alarm function, press the AL1 button once for Alarm 1. You
should now see the Alarm ((1)) symbol to represent the Alarm 1 being ON.
5. To de-activate, press the AL1 button once again.
Date (flashing) Month Weekday Date
(flashing) (flashing) (flashing)