Care And Maintenance - TFA Dostmann 30.3006 Manual De Instrucciones

The range of the Temperature Transmitter may be affected by the temperature. At
cold temperatures the transmitting distance may be decreased. Please bear this in
mind when positioning the transmitter. The LCD contrast on the unit may also be
reduced and the batteries are reduced in power.
433MHZ RECEPTION CHECK
The Temperature station will receive the temperature data within 15 minutes. If the
temperature data is not being received 15 minutes after setting up, the display
shows "- - -" then please check the following points:
1. The distance of the Temperature Station or transmitter should be at least 1.5
to 2 meters away from any interfering sources such as computer monitors or
TV sets.
2. Avoid placing the receiver onto or in the immediate proximity of metal window
frames.
3. Using other electrical products such as headphones or speakers operating
on the same signal frequency (433MHz) may prevent correct signal
transmission and reception.
4. Neighbours using electrical devices operating on the 433MHz signal
frequency can also cause interference.
Note:
When the 433 MHz signal is received correctly, do not re-open the battery cover of
either the transmitter or Temperature Station, as the batteries may spring free from
the contacts and force a false reset. Should this happen accidentally then reset all
units (see Setting-up above) otherwise transmission problems may occur.
The transmission range is around 20 - 25 m from the transmitter to the
Temperature station (in open space). However, this depends on the surrounding
environment and interference levels. If no reception is possible despite the
observation of these factors, all system units have to be reset (see Setting-up).
POSITIONING THE TEMPERATURE STATION:
The Temperature station comes attached with a removable table stand, which
provides the option of table standing or wall mounting the unit.
Before wall mounting, please check that the outdoor temperature(s)
can be received from the desired location(s). To wall mount:
1. Fix a screw (not supplied) into the desired wall, leaving the
head extended out the by about 5mm.
2. Remove the stand from the Temperature station by pulling it
away from the base and hang it onto the screw. Remember
to ensure that it locks into place before releasing.
POSITIONING THE OUTDOOR TEMPERATURE TRANSMITTER
The Temperature Transmitter is supplied with a holder that
may be attached to a wall with the three screws supplied. To
attach to the wall, please follow the steps
1. Mark the wall using a pen through the holes in the holder
to obtain the exact drilling position.
2. Drill holes in the wall at the points marked.
3. Screw holder onto wall.
There is also double sided tape included with the wall mount. On smooth surfaces
this can be used instead of drilling holes. The surface can, however, affect the
transmission range. If for example the unit is attached to a piece of metal, it may
then either reduce or increase the transmitting range. For this reason, we
recommend not placing the unit on any metal surfaces or in any position where a
large metal or highly polished surface is in the immediate proximity (garage doors,
double glazing etc.). Choose a sheltered place. Avoid direct rain and sunshine.
Before securing in place, please ensure that the Temperature Station can receive
the signal from the Temperature Transmitter at the positions that you wish to situate
them. The Temperature Transmitter simply clicks in or out of the holder. When
inserting or removing the Temperature Transmitter to or from the wall holder please
hold both units securely.

CARE AND MAINTENANCE:

•
Extreme temperatures, vibration and shock should be avoided as these may
cause damage to the units and give inaccurate forecasts and readings.
•
When cleaning the displays and casings, use a soft damp cloth only. Do not
use solvents or scouring agents as they may mark the LCD and casing.
•
Do not submerge the units in water.
•
Immediately remove all low powered batteries to avoid leakage and damage.
Replace only with new batteries of the recommended type.
•
Do not make any repair attempts to the unit. Return it to its original point of
purchase for repair by a qualified engineer. Opening and tampering with the
unit may invalidate its guarantee.
•
Do not expose the unit to extreme and sudden temperature changes, as this
may lead to rapid changes in forecasts and readings and thereby reduce its
accuracy.
SPECIFICATIONS:
Temperature measuring range
Indoor : -9.9ºC to +59.9ºC with 0.1ºC resolution
("OFL" displayed if outside this range)
Outdoor : -30ºC to +70ºC with 0.1ºC resolution
below: