Ajuste Y Sustitución De Componentes; Consejos Generales - Skymsen PA-141 Manual De Instrucciones

5.2 Ajuste y Sustitución de Componentes
5.2.1Para afilar las Cuchillas
Las cuchillas son removibles, y pueden fácilmente ser afiladas. Hay que dar atención especial para que el
ángulo de corte sea mantenido. Las cuchillas deben ser afiladas usando una lija fina, o una piedra de afilar.
Para remover las cuchillas
Use un destornillador.
5.2.2Correas de Transmisión
Para un buen desempeño de la maquina y para la durabilidad de las correas, ellas deberán estar en
perfecta tensión. Para mejorar el acceso a las correas, coloque la maquina con los pies para arriba.
Con el auxilio de una llave de tuerca de 9/16", afloje las tuercas (00108.2) y retire los piés ( 00027.2)
girandolos en el sentido anti horario.
Con un destornillador,retire el tornillo ( 00716.1 ), que fija la protección inferior ( 00116.3 ). Después de
haber retirado la protección inferior , con una llave de tuerca de 9/16' afloje los tornillos (00241.0 ) y con el
auxilio de una palanca de madera, empuje el motor en el sentido adecuado para que resulte la mejora de la
tensión de las correas, y después apriete otra vez los tornillos .
Todos los códigos mencionados en este capitulo están en el dibujo explotado de la pagina.
5.3 Diagrama eléctrico Mod. PA -141

6. CONSEJOS GENERALES

- Do not wear loose fitting clothes while operating the unit. Do not use bracelets or any other piece of jewelry. Have
your hair always shortened and held up (use hair fishnets if necessary) in a way it cannot reach any part of the
machine. Roll up any loose sleeves.
- SKYMSEN is not responsible for any harm or injury caused by the negligent or inappropriate use of this
equipment by any operator. This equipment must be operated only by persons whose age equals or exceeds 18
years old, in a safe and sound state of mind, free from the influence of any kind of drugs and alcohol, that received
proper training and instructions regarding the correct operation of this machine, that are wearing correct and
authorized safety clothes. All and any kind of modifications carried on and applied to this machine immediately
nullifies any kind of warranty and may result in harm and injuries to the individuals operating this machine and to
individuals that are located in the machine surrounding areas while it is being operated.
- Under no circunstances place your hands in the moving parts of the machine while it is being used. Make sure the
machine has come to a complete stop before acessing the processed ingredients.
27
3.4.1Cautions with Stainless Steel:
The Stainless Steel may present rust signs, which ARE ALWAYS CAUSED
BY EXTERNAL AGENTS, especially when the cleaning or sanitization is not
constant and appropriate.
The Stainless Steel resistance towards corrosion is mainly due to the
presence of chrome, which in contact with oxygen allows the formation of a very
thin protective coat. This protective coat is formed through the whole surface of the
steel, blocking the action of external corrosive agents.
When the protective coat is broken, the corrosion process begins,
being possible to avoid it by means of constant and adequate cleaning.
Cleaning must always be done immediately after using the
equipment. For such end, use water, neutral soap or detergent, and clean the
equipment with a soft cloth or a nylon sponge. Then rinse it with plain running
water, and dry immediately with a soft cloth, this way avoiding humidity on surfaces
and especially on gaps.
The rinsing and drying processes are extremely important to prevent
stains and corrosion from arising.
Acid solutions, salty solutions, disinfectants and some sterilizing
solutions ( hypochlorite s, tetravalent ammonia salts, iodine compounds,
nitric acid and others), must be AVOIDED, once it cannot remain for
long in contact with the stainless steel:
These substances attack the stainless steel due to the CHLORINE on
its composition, causing corrosion spots (pitting).
Even detergents used in domestic cleaning must not remain in
contact with the stainless steel longer than the necessary, being mandatory to
remove it with plain water and then dry the surface completely.
Use of abrasives:
Sponges or steel wool and carbon steel brushes, besides scratching
the surface and compromising the stainless steel protection, leave particles that rust
and react contaminating the stainless steel. That is why such products must not be
used for cleaning and sanitization. Scrapings made with sharp instruments or
similar must also be avoided.
Main substances that cause stainless steel corrosion:
Dust, grease, acid solutions such as vinegar, fruit juices, etc., saltern
solutions (brine), blood, detergents (except for the neutral ones), common steel
particles, residue of sponges or common steel wool, and also other abrasives.
IMPORTANT
08