Setting The Clock; Operating The Radio - Makita BMR100 Manual De Instrucciones

Slide Battery:
9.6V: BH9033 | BH9033A | BH9020 | BH9020A
12V: BH1233 | BH1233C | BH1220C
14.4V: BH1433 | BH1420 | BL1430
18V: BL1830
24V: BH2433 | BH2420
The following tables indicate the operating time on a
single charge.
Battery Cartridge•Voltage
Battery
Capacity
9.6V 12V
PA09 PA12
1.3 Ah
9120 1220
1.5 Ah – –
9122
1222
2.0 Ah BH9020
BH1220C
BH9020A
2.6 Ah 9134 1234
3.0 Ah 9135 1235
BH9033 BH1233
3.3 Ah
BH9033A BH1233C
* Operating time may differ by the type of battery, charging or
operating conditions.
3-1. Installing or removing Slide
battery cartridge (Fig. 3)
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
• To remove the battery cartridge, withdraw it from the
tool while sliding the button on the front of the cartridge
or pressing the buttons on both sides of the cartridge.
3-2. Installing or removing Cluster
battery cartridge (Fig. 4)
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
• To remove the battery cartridge, withdraw it from the
Job site radio.
4. Replace battery compartment locker.
5. Reduced power, distortion and a "stuttering sound" or
low battery sign
all the signs that the main battery pack needs to
replace.
Note:
The battery pack can't be charged via the supplied AC
power adaptor.
8
Operating time*
(At Max. Volume)
14.4V 18V 24V
PA14
PA18 – Approx. 7 hour
1420
– BL1815 – Approx. 8 hour
1422
1822 BH2420 Approx. 11 hour
BH1420
1434 1834 – Approx. 13 hour
1435 1835
– Approx. 16 hour
BL1430 BL1830
BH1433 – BH2433 Approx. 17 hour
that appears on the display are
6. When low battery sign
on flashing is the time to replace the back up batteries.
Installing the Soft bended rod
antenna (Fig. 5)
Install the Soft bended rod antenna as show in the figure.
Using Supplied AC power adaptor
(Fig. 6)
Remove the rubber protector and insert the adaptor plug
into the DC socket on the front side of the radio. Plug the
adaptor into a standard mains socket outlet. Whenever
the adaptor is used, the battery pack are automatically
disconnected. The AC adaptor should be disconnected
from the main supply when not in use.
Note:
When your radio has any interference in AM band by its
adaptor, please move your radio away from its AC
adaptor over 30 cm.

Setting the clock

1. Clock can be set either when the radio is power on or
off.
2. Display will show "-: - -" when the back up batteries
are installed.
3. Long press the time set button
2 seconds, display will flash time set symbol
also the hour digit, followed by a beep.
4. Rotate Tuning control to set the required hour.
5. Press button to confirm hour setting, the minute
digit will flash.
6. Rotate Tuning control to set the required minute.
7. Press the button again to complete clock setting.

Operating the radio

This radio equips with three tuning methods – Scan
tuning, Manual tuning and Memory presets recall.
Scan Tuning
1. Press the Power button to turn on the radio.
2. Select the required waveband by pressing the Band
button. Make sure the rubber bended rod antenna has
been well placed for best FM reception. For AM (MW)
band, rotate the radio to get best signal. Try to avoid to
operate the radio next to computer screen and other
equipment which will cause interference to the radio.
3. Press and release Scan button (long press Scan
button more than 2 seconds will activate time setting),
LCD display will flash Scan symbol and the radio will
up search and stop automatically when it finds a radio
station,. Press the Scan button again to pick up the
found station.
Note:
A stereo symbol will appear on the display, if the
station found is a stereo station.
appears and an "E" keeps
for more than
and