Setting The Alarm Clock - Makita LXRM03 Manual De Instrucciones

2. Rotate the Tuning control
clock symbol appear on the display. Press the Tuning
control to enter the setting.
3. Rotate the Tuning control
on the display. Press the Tuning control
confirm the setting. The clock time of the radio will set
up automatically according to the RDS data received.
4. When the action is completed, the RDS icon will
appear on the LCD display indicating the radio time is
RDS clock time. The radio cock time will be valid for
5 days each time the radio time is synchronized with
RDS CT.

Setting the alarm clock

Your LXRM03 has two alarms which can each be set to
wake you to AM/FM radio or buzzer alarm. The alarms
may be set while the unit is in standby mode or while
playing.
a. Setting radio alarm time:
1. The radio alarm can be set either when radio is on or
off.
2. Press and hold the radio alarm button
radio alarm symbol and the display hour will flash
along with a beep.
3. During radio alarm symbol
Tuning control knob
Tuning control knob
Then rotate the Tuning control knob
minute and press Tuning control knob
minute setting.
4. Rotate the Tuning control knob and the display will
show the frequency options for the alarm.
The alarm options are as follows:
ONCE - the alarm will sound once
DAILY - the alarm will sound everyday
WEEKDAY - the alarm will sound only on weekdays
WEEKEND - the alarm will sound only at weekends
Press the Tuning control
5. During radio alarm symbol is flashing, rotate Tuning
control knob to select desired wake-up band and
station, then press Tuning control knob to confirm the
selection.
6. Rotate Tuning control knob to select the desired
volume and press Tuning control knob to confirm the
volume. Radio alarm setting is now completed.
Note:
If new radio alarm station is not selected, it will select
the last alarm station.
Note:
If the selected AM/FM alarm station is not available
when the alarm is sounding, the buzzer alarm will be
used instead.
10
until "RDS CT" and a
until "RDS CT" appears
to
, the
flashes, rotate
to select the hour and press
again to confirm hour setting.
to select the
to confirm
to confirm the setting.
b. Setting HWS (Humane Wake System) buzzer alarm:
A beep tone will activate when selecting the HWS buzzer
alarm.
The alarm beep will sound shorter every 15 seconds for
one minute followed by one minute silence before
repeating the cycle.
1. The buzzer alarm can be set either when the radio is
on or off.
2. Press and hold the buzzer alarm button
symbol and the display hour will flash along with a
beep.
3. During buzzer alarm symbol
Tuning control knob
Tuning control knob
Then rotate the Tuning control knob
minute and press Tuning control knob
minute setting.
4. Rotate the Tuning control knob and the display will
show the frequency options for the alarm.
The alarm options are as follows:
ONCE - the alarm will sound once
DAILY - the alarm will sound everyday
WEEKDAY - the alarm will sound only on weekdays
WEEKEND - the alarm will sound only at weekends
Press the Tuning control
Note:
There is no volume adjustment for buzzer alarm.
When the alarm sounds
To cancel a sounding alarm, press the Power button
.
Disabling/cancelling alarms
To disable an active alarm, either press the Power button
, or press and hold the corresponding alarm button to
cancel the alarm.
Snooze
1. When the alarm sounds, press any button other than
the Power button will silence the alarm for 5 minutes.
"SNOOZE" will appear on the display.
2. To adjust the silence time for the snooze timer, press
and hold the Menu/Info button
setting.
3. Rotate the Tuning control
appears on the display, then press the Tuning control
to enter the setting. Rotate the Tuning control
to adjust the silence time from 5, 10, 15 and
20 minutes for the snooze timer.
4. To cancel the snooze timer while the alarm is
suspended, press the Power button
, the
flashes, rotate
to select the hour and press
again to confirm hour setting.
to select the
to confirm
to confirm the setting.
to enter the menu
until "SNOOZE X"
.