Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
TO BE REMOVED BYTHE
CUSTOMER
AFTER iNSTALLATiON
IS COMPLETE
f
[]
iNSTALLATION
CHECKOFF
LIST
[]
[]
[]
[]
f
DOORS
[]
Handles are secure and tight
[]
Door seals completely to cabinet on all sides
[]
Freezer door is level across the top
Leveling
[]
Refrigerator is level, side to side and tilted 1/4" (6mm) front to back
[]
Toe grille is properly attached to refrigerator
[]
Cabinet is setting solid on all corners
Electrical Power
[]
House power turned on
[]
Refrigerator plugged in
ice Maker
[]
House water supply connected to refrigerator
[]
No water leaks present at all connections - recheck in 24 hours
[]
Ice Maker is turned ON.
Final Checks
Shipping material removed
Fresh Food and Freezer controls set
Crisper Humidity controls set
Registration Card sent in
Tools Necessary:
Phillips"
head
Quodrex
hood
screwdriver
1
%
f
2
Socket
Wrench
Set
Adjustable
Wrench
HAND TRUCKING
,, Load refrigerator from side of cabinet only.
,, Do not run retaining straps over handles.
,, Do not over-tighten
retaining straps.
,, Never use refrigerator
handles to move the
refrigerator.
,, Remove tape from doors only after unit is in
place.
1 Piece
of Ta#e
2 Pieces of Tape
- -
2 Piece8
of Tape
.-f"
2 Pieces of T_pe .........
4 Pieces of TapeJ
Toe Grille
r--"
J
2 Pieces of Foam_
SHIPPING
MATERIAL
. !OD
1 ....... fT_l \
2 Pieces
of Foam .........
I
-
1 Piece
ol Tape
1 Piece
of _hpe
"_
2
I:_ieees
of I_pe
...... 2 Pieces
of Tape
"\"
2 _:'_eees of I_pe
"-_2
P_eees
ef Tape
Remove Shipping material. (Features
may vary per model.)
3
WATER SUPPLY
Plastic
Water
Connect water supply - check for water
leaks. Turn icemaker OFF if water supply
is not connected
immediately.
Connecting
to a reverse osmosis system
is not recommended.
gliii!iiijli
J
INSTALLATION
CLEARANCES
Allow the following clearances for ease of installation, proper air circulation, and
plumbing and electrical connections:
,,
Sides & Top .......... 3/8"
*
Back ....................... 1"
4
f
-,
LEVELING
AND ADJUSTING
All four corners of your refrigerator must rest firmly on a solid floor. Your refrigerator
is equipped with adjustable front rollers or front leveling screws to help level your
unit.
To level cabinet or change door height:
1. Remove toe grille.
2. Use flat-blade screwdriver or 3/8" socket wrench to adjust front rollers. Use
adjustable wrench to adjust leveling screws.
Toe Grille
Adjustable Front Roller
(some models)
Stationary
Front Roller
with Leveling Screw
(some models)
Humidity
""H_h'd'ty_-_)_
o
6
CONTROLS
When changing controls, wait 24
hours before making additional
adjustments.
/
7
ICEMAKER
Ensure icemaker
is turned ON.
[/"/_,//_
Signal Arm
f
if you need to remove the doors to get your refrigerator
into the house please see "Door Removal and Reversal
instructions"
in your Use & Care Manual.
DOOR
REMOVAL
(iF NECESSARY)
Cable
Bottom
ube
,J
Shim
Center
See "Normal
Operating
Sights & Sounds" in the Use & Care Manual
so you understand the sounds you may hear once your refrigerator is
running.
Please read entire Use & Care Manual to become aware of important
safety instructions and to become familiar witrh your new refrigerator.
Send in Registration
card to register your refrigerator.
Congratulations!
You are ready to enjoy your new refrigerator.
OR_
iii
Publicidad
