Garmin VECTOR Guia De Inicio Rapido página 2

6
Rotate the crank arm to check for clearance.
The pedal pod should not interfere with any part of the bike.
7
Use the pedal wrench to tighten the spindle.
nOTE: Do not overtighten. Garmin recommends torque of 25 to 30 lbf-ft. (34
to 40 N-m).
8
Firmly plug the cable into the spindle.
9
Rotate the crank arm to check for clearance.
10
Repeat steps 2–9 to install the right pedal.
nOTE: If the pedal pod cable rubs the chain, you can add washers between
the pedal pod and the crank arm to increase clearance.
installing the Shoe Cleats
nOTE: The left and right cleats are the same.
1
Apply a thin layer of grease on the cleat bolt threads.
2
Align the cleat , washers
➊ ➋
➌
➋
➊
3
Use a 4 mm hex key to loosely attach each bolt to the sole of the shoe.
4
Adjust the cleat to the shoe in your preferred position.
This can be adjusted after a trial ride.
5
Tighten the cleat firmly to the shoe.
nOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-m).
adjusting the release Tension
Do not overtighten the release tension screw on the bottom of the pedal. The
release tension should be adjusted equally for both pedals.
Use a 3 mm hex key to adjust the release tension of each pedal.
There is a window on the back of the pedal binding that shows the allowable
range.
Pairing Vector with Your Edge
Before you can view Vector data on the Edge
Pairing is the connecting of ANT+
This procedure contains instructions for the Edge 810. If you have another
compatible device, see your owner's manual or go to
vectorowner.
1
Bring the Edge within range (3 m) of the sensor.
nOTE: Stay 10 m away from other ANT+ sensors while pairing.
2
Turn on the Edge.
3
From the home screen, select
4
Select a profile.
5
Select .
6
Enable the sensor, and select Search.
7
Rotate the crank arm a few times.
When the sensor is paired with your Edge, the sensor status is Connected.
You can customize a data field to display Vector data.
Going for Your First ride
Before you ride with Vector for the first time, you must enter the crank length, set
the install angle of the sensors inside the pedals, and calibrate the static zero
reference.
Entering the Crank Length
The crank length is often printed on the crank arm.
2
, and bolts .
➌
notice
, you must pair the devices.
®
wireless sensors.
™
www.garmin.com/
> Bike Profiles.
1
Rotate the pedals a few times in order to activate Vector.
2
From the home screen, select
3
Select a profile.
4
Select Crank Length > Manual.
5
Enter the crank length, and select
Setting the installation angle
Before you set the installation angles, you must set the Edge data fields to
display power and cadence.
You can go for a short ride on a trainer or on the road.
1
Ride until the cadence is nearly 70 rpm.
2
Accelerate smoothly to approximately 90 rpm.
When the installation angles are successfully set, a message appears and
data fields display power data on the Edge.
Performing a Static Zero Calibration
nOTE: During this task, the bike must be in an upright position and nothing can
be touching the pedals.
1
From the home screen, select
2
Select a profile.
3
> Calibrate.
Select
When the zero reference is determined, a message appears on the Edge.
Calibrating Vector Before Each ride
For best results, Garmin recommends calibrating Vector at the start of every ride.
1
Perform a static zero calibration
2
Go for a ride.
3
While coasting, smoothly pedal backwards 5 consecutive times or more.
When Vector is calibrated, a message appears on the Edge.
Troubleshooting
Getting the Owner's Manual
You can get the latest owner's manual from the web.
1
Go to www.garmin.com/vectorowner.
2
Click Manuals.
Vector Storage
If you are transporting your bicycle or not using Vector for an extended period of
time, Garmin recommends removing Vector and storing it in the product box.
> Bike Profiles.
.
> Bike Profiles.
(page 2).