Numark NS6II Guia De Inicio Rapido página 8

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

22. Bleep / Keylock: Press this button to reverse audio playback of the track on the corresponding
deck. Press this button again to resume normal playback from where it would have been if you
had never engaged the Bleep function (i.e., as if the track had been playing forward the whole
time).
Press and hold Shift and then press this button to activate or deactivate Keylock: the key of the
song will lock to whatever position the pitch fader is at when Keylock is activated. This feature
allows you to change the speed of the song without changing the key.
23. Scratch: Press this button to activate or deactivate Scratch Mode. In this mode, you can touch
the center part of the platter will scratch like a turntable when you spin it. If Scratch Mode is off,
the center part of the platter will pitch-bend when you spin it.
Press and hold Shift and then press this button to toggle between time elapsed and time
remaining in the jog wheel display of the corresponding deck.
24. Strip Search: The length of this strip represents the length of the entire track. Place your finger
on a point along this sensor to jump to that point in the track. (If you want to scroll through a
track, we recommend using your computer rather than running your finger along the strip.)
25. Slip / Quantize: When using the software's Beat Grid, hold Slip and move the platter to "slip"
(i.e., shift or slide) the entire Beat Grid to the left or right. This is helpful when the Beat Grid is
slightly misaligned with the track's transients. See the Serato DJ manual for more information.
Press and hold Shift and press the Deck A (left side) Slip button to enable or disable Quantize
for Layer 1 or 3. Press and hold Shift and press the Deck B (right side) Slip button to enable or
disable Quantize for Layer 2 or 4. When enabled, setting and triggering cues and loops will snap
to the Beat Grid.
Pad Mode Controls
26. Pads: These pads have different functions on each Deck depending on the current Pad Mode.
These pads are the same pads used with Akai Professional MPCs, so they are velocity-sensitive
(in certain modes only), durable, and easy to play.
27. Parameter < / >: Use these buttons for various functions in each Pad Mode. Press and hold
Shift and use these buttons to access secondary parameters.
If you have purchased the Serato Pitch N' Time expansion, pressing and holding Shift and then
pressing these buttons will adjust the Key of the current track down (<) or up (>).
28. Cues: This Pad Mode button switches the pads between two modes: Hot Cue Mode and Hot
Cue Auto-Loop Mode. When the button is unlit, the first press will always select Hot Cue Mode.
Please see the User Guide for more information.
29. Auto / Roll: This Pad Mode button puts the pads in two modes: Auto-Loop Mode and Loop Roll
Mode. When the button is unlit, the first press will always select Auto-Loop Mode. Please see
the User Guide for more information.
30. Loop: This Pad Mode button switches the pads between two banks of saved loops and Manual
Loop controls. When the button is unlit, the first press will always select the first bank. Please
see the User Guide for more information.
31. Sampler: This Pad Mode button switches the pads between two modes: Sample Player Mode
and Sample Velocity Trigger Mode. When the button is unlit, the first press will always select
Sample Player Mode. Please see the User Guide for more information.
32. Slicer: This Pad Mode button switches the pads between two modes: Slicer Mode and Slicer
Loop Mode. When the button is unlit, the first press will always select Slicer Mode. Please see
the User Guide for more information.
Important: Your track must have a set Beat Grid for Slicer Mode or Slicer Loop Mode to work.
8

Publicidad

Tabla de contenido
loading

Tabla de contenido