Bosch Active Line Nyon Manual Original página 23

Operating mode "Settings"
This operating mode allows you to set the basic configura-
tions of your on-board computer.
Note: Some basic configurations can only be changed when
Nyon is inserted into the holder 4.
To reach the "Settings" menu, press the joystick 1 down in
the main menu until "Settings" is displayed.
Tip: If you press the joystick down long enough, you will also
reach the "Settings" menu.
The following configurations can be made:
– "Connections": You can configure the Bluetooth® config-
urations, a new smartphone connection, a WiFi connection
or a heart rate monitor.
When you enable WiFi, Nyon searches for available net-
works. Found networks will be displayed. Use the joystick
1 to select the desired network and enter the password.
– "Map&Navigation": Here you can configure the map dis-
play and turn on automatic adaptation of the display, de-
pendant on the ambient brightness.
– "My Profile": Here you can also choose to display the
active user.
– "My eBike": When Nyon is plugged in, you can change the
pre-set value given by the manufacturer of the wheel cir-
cumference by ±5 %.
The bicycle manufacturer or dealer may base the service
date on the distance travelled and/or a period of time. The
due date for the service is displayed under "Service".
Under "Shift Recommendation", you can switch the indi-
cation of a shift recommendation on and off.
If your eBike is equipped with "eShift", you can also con-
figure your eShift system here (see "eShift (optional)",
page English–9).
– "My Nyon": Here you can search for updates, configure
the Home button, automatically set the counters such as
trip meter, calories burned and average values to "0" every
night, or reset Nyon to the factory settings.
Under "Auto Brightness", the brightness of the display
can be automatically adjusted.
Under "Altitude correction", you can adjust the value dis-
played to the actual altitude to compensate for weather-re-
lated changes.
– "Region & Language": You can set speed and distance in
kilometres or miles, display clock in 12 or 24 hour format,
select the time zone and set your preferred language. The
current time is automatically taken from the GPS signal.
– In the "Help" menu item, you will find a selection of FAQs
(frequently asked questions), contact details and informa-
tion about the system and licenses.
Bosch eBike Systems
Status display
Depending on the operating mode shown, all status indica-
tors are not always displayed. Indicators already shown on
the main screen will not be shown again. The position of the
indicators may vary. If the on-board computer is taken out of
its holder, the charging state of the Nyon battery of the on-
board computer is displayed in place of the bike lights indica-
tor.
s1 s2
14:30
s5 s6 s7 s8
s1 Bike lights display/Charge level indicator of Nyon battery
pack
s2 Clock display
s3 Speed display
s4 North display
s5 Bluetooth®/WiFi connection display
s6 Assistance level display
s7 Charge level indicator of the eBike battery pack
s8 GPS signal display
s9 Zoom range/remaining range display
s10 Shift recommendation
Energy supply of the on-board computer
If the on-board computer is in the holder 4, a sufficiently
charged eBike battery pack is inserted into the eBike and the
eBike system is turned on, then the Nyon battery pack is pow-
ered by the eBike battery pack.
If the on-board computer is removed from the holder 4, the
energy is supplied via the Nyon battery pack. If the Nyon bat-
tery pack is weak, a warning message appears on the display.
To charge the Nyon battery pack, insert the on-board comput-
er back into the holder 4. Note that if you do not charge the
eBike battery pack straight away, the eBike system will auto-
matically switch off after 10 minutes of inactivity. In this case,
the charging of the Nyon battery pack will also cease.
English–7
s3 s4
2 22
km/h
100 m
s10
105 km
s9
1 270 020 XBN | (12.5.16)