Special Safety Instructions - Metabo KHE 5-40 Instrucciones De Manejo

be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
2.5 Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
2.6 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

3. Special Safety Instructions

Wear ear protectors. Exposure to noise can
cause hearing loss.
Use the auxiliary handle(s) supplied with the
tool. Loss of control may cause personal injury.
Hold the power tool by the insulated gripping
surfaces when performing an operation where
the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
Pull the plug out of the socket before making any
adjustments, changing tools, maintaining or
cleaning.
Always work with the additional handle correctly
installed.
Always hold the machine with both hands on the
intended handles, take a secure stance and
concentrate on the work.
Always wear protective goggles, gloves, a dust
mask and sturdy shoes when working with this tool.
Ensure that the place where you wish to work is free
of power cables, gas lines or water pipes (e.g.
check using a metal detector).
Work only with a correctly fitted tool. Pull on the tool
to check that it is correctly seated. (It must be
possible to move the tool a few centimetres in an
axial direction.)
When working above ground level, ensure that the
area below you is clear.
Never touch the tool or parts near the tool directly
after work because they may be extremely hot and
can cause burns to the skin,
Always position the power cable so that it leads
away from the back of the machine.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Secure the workpiece to prevent slipping or rotation
(e.g. by securing with screw clamps).
Reduce dust exposure:
Some of the dust created using this power tool
may contain chemicals known to cause
cancer, allergic reaction, respiratory disease, birth
defects or other reproductive harm. Some
examples of these chemicals are: Lead from lead-
based paints, crystalline silica from bricks and
cement and other masonry products, arsenic and
chromium from chemically-treated lumber, hard
wood like oak or beech, metals, asbestos.
The risk from exposure to such substance will
depends on how long you or bystanders are being
exposed.
Do not let particles enter the body.
To reduce your exposure to these substances: work
in a well ventilated area, and work with approved
safety equipment, such as dust masks that are
specially designed to filter out microscopic
particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
ENGLISH en
5