Operating - Bosch SHE6AP02UC/03 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Operating
the Dishwasher
SHX4AP, SHX5AL, SHX6AP
Off
@
6_,e
(
P....
Auto
Regular Delicate
Quick
RJ .....
........
9h®
/
Sc,ub
Wash
Wash
Wash
Wash
&Hold
<
\
_;/Clean
O R nseAgent
Delay
Haft Load
Program
Select
Depending on your model you wifl either have 4, 5 or 5 wash
cydes.
To start the dishwasher:
Open the Door. Press the"ON/OFF"
button.
One of the Wash Cycle LEDs will be flashing. You can
now select a wash cycle.
Press the "<" or ">" button to select the desired wash
cycle.
Press the "START" button (LED stops flashing)
Close the door to begin the cycle
NOTE
1.
Rinse Agent Indicator
Light will be illuminated
if the
unit needs Rinse Agent.
2.
If you close the door without
pressing the start button
the unit will beep.
To cancel a cycle:
Open the dishwasher
door just far enough to expose
the control panel. Be careful of hot water splash out!
fou could be seriously scalded if you allow hot water to
_plash out of the dishwasher. OPENTHE DOOR CAREFULLY
:luring any wash or rinse cycle. Do not fully open the door
until water noises have stopped.
Press and hold the "START/RESET" button
until the
"Active" indicator light goes out.
Close the door and wait for about
1 minute for the
dishwasher to drain.
Open the door and press the"ON/OFF"
button.
You are now ready to start a new cycle.
To enter
the options
mode(rinse
agent
setting,
extra
dry heat, cycle completion
signal):
Door must be open. Press the "ON/OFF" button
to
turn the unit on.
One of the Wash Cycle LEDs will be flashing.
Press and hold down the ">" button,
then press and
release the "START/RESET" button.
Now release the
">" button.
18
The "Clean" and one other LED will be flashing. You are
now in the options setup mode.
Press ">" to select the option you would like to adjust.
If the "Clean" and "Rinse Agent" LED are flashing you can
adjust the Rinse Agent settings.
If the "Clean" and "Sanitized"
LED are flashing you can set
the Extra Dry Heat.
To set the amount
of Rinse Agent:
NOTE: If your glasses have spots on them, you need more
rinse agent. If your glasses have streaks, you need less
Rinse Agent.
Follow the prior instructions
to enter "options" mode. With
the "Clean" and "Rinse Agent" LEDs flashing:
Press the "<" button
to change the amount
of rinse
agent dispensed.
0 LEDs flashing --> Rinse Agent dispenser is OFF
1LED flashing --> Lowest amount of rinse agent
2 LEDs flashing --> Medium amount dispensed
3 LEDs flashing --> Highest amount of rinse agent
Press "START"to save your settings.
To turn Extra Dry Heat on or off:
With the "Clean" and "Sanitized" LEDs flashing:
Press the "<" button to turn Extra Dry Heat on or off.
The wash cycle LEDs will illuminate
when you press
II_II
0 LEDs flashing --> Extra Dry Heat is OFF
1LED flashing --> Extra Dry Heat is ON
To set the Cycle Completion
Signal:
With the "Clean",
"Sanitized",
and "Rinse Agent" LEDs
flashing:
Press the "<" button
to change the cycle completion
tone level. The wash cycle LEDs will illuminate
when
you press "<".
0 LEDs flashing --> Cycle Completion Signal is OFF
1LED flashing --> Low tone level
2 LEDs flashing --> Medium tone level
3 LEDs flashing --> Highest tone level
Press STARTto save your settings.

Publicidad

Tabla de contenido
loading

Tabla de contenido