Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
selected cleaning time has elapsed. This will repeat in accordance with
your chosen cleaning frequency.
The "AUTO START" function can be stored for 15 days.
If the cleaner is disconnected from the power supply for more than 15
days, the
power supply must be restored for at least an hour to re-activate the
function.
Hints and tips
To allow the cleaner to work optimally, set the pH of the water between
7.0 and 7.4; the water temperature should be between 12°C and 35°C.
We recommend keeping the cleaner between 5°C and 40°C in a well
ventilated place out of direct sunlight. The mains cable
should be coiled around the cable holder for storage.
Avoid direct sunlight at all times!
In addition, secure the control unit with a cord so that the power pack
cannot be pulled through the pool by the cleaner.
Features of the control unit (Ill. 9)
Symbols
Comment
ON/OFF
Start/Stop
AUTO
Auto-start function
START
1H fl ashing
1.5H fl ashing
2H fl ashes
Cycle light
1H, 1.5H, 2H fl ashing
simultaneously
1D constant
3D constant
Auto-start
monitoring light
7D constant
1D,3D,7D fl ashing
Monitoring
Symbols
light
1H and
1.5H
fl ashing with
acoustic
signal
1.5H and
2H fl ashing
Diagnostics
with
acoustic
signal
1H and 2H
fl ashing with
acoustic
signal
Care and maintenance
The cleaner turns itself off automatically after a cleaning
cycle. Unplug the mains cable, gently pull the cable, and lift the cleaner
out of the water using the handle.
Caution:
8
Function
Press once to start, press
again to stop.
This feature enables the
automatic activation of the
cleaner's programming.
When the robot stops, if
all the lights go extinguish
after 5 seconds, it is in
rest mode. if the three
lights 1D, 3D, and 7D are
off, press AUTO START
to see if it is still working.
If the three lights are
fl ashing at the same time,
it means that it is not in
operation.
Cleaning in 1 hour
Cleaning in 1.5 hours
Cleaning in 2 hours
Cleaning fi nished
Auto-start programmed
daily
Auto-start programmed
every 3 days
Auto-start programmed
every 7 days
No auto-start
Error
Recommended solution
Stop the robot and check
that the running wheel is
not blocked by a foreign
Pump
object.
overloaded
Check to see if a foreign
object is caught in the
belts.
Motor over-
loaded
Resubmerge
the
robot
in
the
water
and,
if
necessary, press the start
Robot is not
button.
in the water
When lifting the cleaner out of the water, you must ensure that the clean-
er does not hit the side of the pool wall, otherwise you may damage both
the cleaner and the liner.
Hold the cleaner above the pool for about 10 to 15 seconds, so that the
water in the cleaner fl ows through the water outlet for the most part into
the pool. Then you can place the cleaner on the edge of the swimming
pool.
It is important to place the cleaner near the edge of the pool, then open
the cover screws and remove the housing cover. Now take out the fi lter
unit and remove the fi lter bag.
When cleaning the fi lter bag, you must remove the dirt from the outside of
the bag with clean water. Then put the bag back in. As a water outlet with
fi lter is built into the cleaner, some dirt may remain in the cleaner, which
should also be rinsed out. Then place the fi lter unit back in completely
alongside the motor. After attaching the housing cover, screw it tight
again.
Caution: Make sure that the lid is properly closed over the housing. To
avoid any damage to the cable or housing, please make sure that both
are in the correct position.
Troubleshooting
Fault
Cause
Cable was not
released properly
The
power cable
is twisted
The cable in the water
or
is too long.
tangled
Cleaner is stuck
on the outlet grille
The power unit is in
the wrong place
Water circulation in
The cleaner
the pool is switched on.
cannot reach
Connection cable
all
is too short
areas.
Filter bag is blocked
Algae is growing
on the walls
Water temperature is
too high/too low
Cleaner does
Brushes are worn out
not
climb up the
pool wall
The cleaner is too
light, it is tilting
PH value is not
correct
Power pack is not fully
plugged in
The cleaner was dam-
Cleaner is
aged during
not
transport.
working
The operating unit
needs a different
voltage to the local
one.
061025_2003
EN
Solution
Switch off the device,
release and uncoil
the cable.
Remove the excess
cable from the
water.
Switch off the fi lter unit.
Position the power unit so
that the cleaner can reach
all areas properly.
Switch off the fi lter unit.
Place the greatest
possible length of connect-
ing cable into the pool, but
bear in mind the corre-
sponding minimum distance
between the
operating unit and the pool
Replace the fi lter bag
Clean the pool walls
Optimal water temperature
is
between 10°C and 35°C
Contact the customer ser-
vice centre, replace
the brushes
Switch the unit off
and allow the air to
escape
Test the pH value, and if
necessary set between 7.0
and 7.4
Check the power cable plug
and the operating
unit.
Contact your retailer
Contact the customer ser-
vice centre
Publicidad
Tabla de contenido
Solución de problemas
