Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
CONNECTION TO OTHER EQUIPMENT
4. To connect the TV to a VCR with an S-VIDEO jack
Set the TV/AV selection for this connection, to AUX1.
If you connect a VCR with an S-video cable to the S-VIDEO jack on the rear of TV, you must also connect the audio cables to
the AUDIO IN jacks on the rear of the TV. The S-video cable only carries the video signal. Audio signal is separate.
VCR
(not supplied) AUDIO (R)
SETTING LANGUAGE
This TV can display the channel number, on screen displays and picture adjustments on the screen in English, Spanish or French.
1
Press ACTION.
2
Press B to select the SET UP
mode, then press ACTION.
NOTE:
All four arrows can be used to select
the SET UP mode, not just B.
NOTE:
If Spanish or French is chosen, the Closed Caption indicators will be in the selected language, but the Closed Caption text will not
be affected by the language selection.
TV OPERATION
1
To turn on the TV, press POWER.
2
The VOLUME can be adjusted to a desired level by
pressing VOL (VOLUME) B or A .
The sound level will be indicated on the TV screen by
GREEN BARS AND A NUMBER. As the sound level
increases, so do the number of BARS AND THE NUMBER
on the screen. The same is true for decreasing the level.
Set the TV/CATV menu option to the appropriate position.
3
When shipped from the factory, this menu option is in the
CATV setting. See "To Memorize Channels".
TV
- VHF/UHF channels
CABLE - CABLE TV channels
4
CH (CHANNEL)
and
Press and release the CH (CHANNEL)
channel automatically stops at the next channel set into
memory. Press and hold the button down to change
channels more quickly.
For proper operation, before selecting channels, they
should be set into the TV's memory. See "To Memorize
Channels".
Rear of TV
IN
VIDEO
ANT(75
)
L/MONO
S-VIDEO
AUDIO
R
AUDIO (L)
(not supplied)
PICTURE
AUDIO
EXIT
LOCK
SET UP
LANGUAGE / IDIOMA / LANGUE
MODE
: CABLE
AUTO PROGRAM
MANUAL PROGRAM
CC
: OFF
/
/
/ ACTION
or
. The
OUT
NOTE: When the S-video cable and the video cable
VIDEO
L/MONO
are connected to each jack at the same time,
AUDIO
the S-video cable takes precedence over the
R
video cable.
3
Press
and then press
select desired language (e.g.
English), then press ACTION.
TIMER
SET UP
4
Press ACTION to select the EXIT mode, then press
ACTION again.
DIRECT CHANNEL SELECTION (0-9) - Press these buttons to
select a channel.The channel number will appear on the upper
right corner of the TV screen. If an invalid channel number is
selected, the display will revert to the previous channel.
TV MODE DIRECT CHANNEL SELECTION - When the TV/
CATV menu option is in the TV position, all channels can be
instantly selected by using two buttons (For example, to select
channel 2, press "0", then "2". If you press only "2", channel
selection will be delayed for a few seconds). For channels 10
and above, press the 2 digits in order.
CATV mode direct channel selection
When the TV/CATV menu option is in the CATV position,
channels can be selected as follows:
1-9
10-12
13-99
100-125
NOTE:
If the station being viewed stops broadcasting, the TV
will automatically shut off after 15 minutes.
(CONTINUED)
or
to
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANÇAIS
Press "0" twice, then 1-9 as needed.
Example, to select channel 2, press "002".
Press "0", then remaining 2 digits.
Example, to select channel 12, press "012".
Press the 2 digits in order.
Example, to select channel 36, press "36".
Press the 3 digits in order.
Example, to select channel 120, press "120".
/
/ACTION
7
Publicidad
Tabla de contenido
