Product Overview; Unique Features; Cellemetry; 900 Mhz, Frequency Hopping Spread Spectrum - DeWalt DS100 Manual De Instrucciones

Sistema de alarma portátil jobsite security
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

PRODUCT OVERVIEW

Unique Features

This system offers several features unique to most security systems.
CELLEMETRY®
Cellemetry® is a patented two-way wireless data network that uses standard cellular infra-
structure to transport small packets of communication messages throughout North America.
The technology is currently used on Verizon, AT&T and Cingular cellular networks
providing a near seamless network on a proven cellular network architecture.
This technology is proven and reliable using the digital control channels, not voice channels.
Messages traverse existing AMPS cellular network infrastructure (like roaming cell phones).
The control channels are more robust than the voice channels because of the use of digital
technology, higher transmission power offering better coverage, and cost effective use due
to small amounts of information being transmitted at a time. The analog cellular network is
one of the largest radio networks in the world with over 200,000,000 packets of data trans-
mitted daily in North America. This only represents 10% of the maximum control channel
capacity.
The DS100 Jobsite Security Portable Alarm System (Base Unit) contains a 1.2 watt
cellular data radio providing rapid communications in less than 1 second. This technology is
superior to phone line monitoring because phone lines are inherently vulnerable, readily
identifiable, and thieves potentially cut them before entering a site.
This product can be used virtually anywhere in North America where cellular coverage is
available, with no roaming fees. See the Coverage Map in the Appendix.
This notification happens instantly and will provide direct feedback when system is armed.
This unique feature helps to provide the ultimate in protection of commercial assets and
rapid response notification.
900 MHZ, FREQUENCY HOPPING SPREAD SPECTRUM (FHSS)
Spread Spectrum is a frequency-hopping communication technique that sends redundant
messages across a bandwidth of at least 10 MHz to provide immunity from interference
and help ensure reliable communication. This communication between the Base Unit and
sensors provides coverage of up to 2000' (6,100m) enabling superior range and reliability.
Virtually all 300MHz systems send information on one narrow band channel. Any "in-band"
interference can result in missed signals.

SYSTEM OVERVIEW

DS100 Jobsite Security Portable Alarm System
(Base Unit)
The DS100 Jobsite Security Portable Alarm System is a portable self-contained alarm
system that can be easily moved from site to site. This system includes a built-in motion
sensor, vibration sensor, siren, strobe, battery back-up, LCD display, key pad interface,
cellular radio receiver-transmitter, wireless sensors receiver-transmitter, phone connector
and AC adaptor.
PRODUCT SPECIFICATIONS
Operating Temperature
Storage Temperature
Maximum humidity
Power Source to
power supply connector
Nominal Range
10˚F – 110˚F (12˚C – 43˚C)
-20˚F – 140˚F (29˚C – 60˚C)
90% relative humidity, noncondensing
110 – 130 Volts AC
up to 2000 feet (6,100m)
ELECTRONIC CHIME TONE
When typing on the keypad, there will be a chime that indicates the key was pressed.
KEY PAD INTERFACE
Refer to Figure 1 at the beginning of this manual.
LED DISPLAY CODES
LED
SOLID
POWER
Primary power
source is present
ARMED
System is armed
CELL
Cellular signal
is strong
CALL
Call is complete
(will remain solid
for 30 seconds)
NAVIGATING THROUGH THE SCREENS
The Base Unit has an LCD screen that will communicate the current state of the unit and
messages will scroll across the screen. Below the screen are four keys that align with avail-
able options. Choose the appropriate key.
LINE 1
LINE 2
ACTUATING
BUTTONS
DOWN UP
LEFT RIGHT
DS200 KEY CHAIN REMOTE CONTROL
The DS200 Key Chain Remote Control offers the benefit of easy one-touch arming or
disarming of the system from a range of up to 2000'. The remote uses 900MHz (FHSS)
communication to provide superior range and reliability. The LED feedback light notifies
the user when a signal is being sent to the Base Unit. Also, a convenient carabiner clip
is included for versatility.
The DS200 Key Chain Remote Control uses a CR-2 3.0 Volt Lithium battery.
To arm the system, press the arm ( ) button and hold until LED flashes. To disarm the
system, press the disarm ( ) button and hold until LED flashes.
1
BLINKING
OFF
• Primary power supply
No unit power
missing (steady flashes);
and no battery
• Low battery (series of two
power
flashes); or
• Standby state (one flash
every 5 seconds)
On an exit or entry delay
System is
disarmed
Cellular signal
Little or no
is weak
cellular signal
Call is in progress
No activity
·

Publicidad

Tabla de contenido
loading

Tabla de contenido