DeWalt DS100 Manual De Instrucciones página 31

DESCRIPTION OF EVENT CODES
Event Code Description
Base: NO AC No power to Base Unit
Base: POWER RESTORED Base Unit power restored
DEV x txt: NO AC No power to device
DEV x txt: POWER RESTORED Device power restored
DEV x txt: LOW BATT Device battery low
DEV x txt: LOW BATT CLR Device battery restored
BASE LOW BATT Battery has dropped below
the voltage limit
BASE LOW BATT CLR Base Unit battery has
been restored
DEV x txt: SIGNAL WEAK Transmission signal from
device is weak
DEV x txt: SIGNAL GOOD Transmission signal from
device now OK
DEV x txt: TAMPER Device has been opened
or damaged
DEV x txt: NO CHECK IN Device check-in messages
have not been received
DEV x txt: NO CHECK IN CLR Device check-in message
has been received
DEV x txt: RESET Device has been reset
DEV x txt: REGISTERED Device has been registered
DEV x txt: REMOVED Device has been
unregistered and removed
from programming
Base: BATTERY FAULT System battery is
defective
Base: BATTERY FAULT CLR Base Unit battery has
been restored
Base Motion: ALARM Base Unit motion
sensor tripped
Base Motion: ALARM CLR Base Unit motion
sensor alarm cleared
Base Vibration: ALARM Base Unit vibration
sensor tripped
Base Vibration: ALARM CLR Base Unit vibration sensor
alarm cleared
Cell Radio: SHUTDOWN Cellular radio has been
shut down
Cell Radio: ACTIVATED Cellular radio has been
reactivated
USER x txt: ARMED or User x or Key Chain
DEV x txt: ARMED (keychain) or Remote x has armed
ARMED (code) the system
USER x txt: DISARMED or User x or Key Chain
DEV x txt: DISARMED (keychain) or Remote x has disarmed
DISARMED (code) the system
Action
Event Code
Check power supply USER x txt: FORCED ARM or
DEV x txt: FORCED ARM (keychain)
NA
or FORCED ARM (code)
Check power supply
Base: AUTOARM
NA
Change battery,
Base: FORCED AUTOARM
reset device
NA
Plug in power supply
Base: CALL SUCCESS
to recharge battery
NA
Base: CALL FAIL
Check for
Base Siren: ENABLED or
interference move
Base Strobe: ENABLED
device location
Base Siren: DISABLED or
NA
Base Strobe: DISABLED
ENTER MASTER MODE
Close device or
or replace if damaged
MASTER MODE TIMEOUT
Check for interference
move device location
EXIT MASTER MODE
NA
USER x: ADDED
NA
NA
USER x: REMOVED
NA
TIME/DATE CHANGED
Needs to be repaired at
FAULTS CLEARED
D WALT authorized
E
service center
DEV x txt: RECEIVER FAULT
NA
DEV x txt: RECEIVER FAULT CLR
Check for intrusion at
Base Unit
DEV x txt: ALARM
NA
DEV x txt: ALARM CLR
Check for intrusion at
Base Unit
CELL RADIO: NO CHECK IN
NA
CELL RADIO: NO CHECK IN CLR
BASE NC: NO CHECK IN
See Troubleshooting;
call customer service
BASE NC: NO CHECK IN CLR
NA
FORCED DISARM
NA
Base: PERIODIC TEST
Base: ALARM CLR
NA
24
DESCRIPTION OF EVENT CODES
Description
User x or Key Chain
Remote x has armed
the system over a fault
System has been
automatically armed
System has been
automatically armed
over a fault
A call has been made
to the monitoring service
A call to the monitoring
service failed
Base Unit siren or strobe
has been enabled
Base Unit siren or strobe
has been disabled
Master user entered
master mode
Master user allowed
system to time out
Master user exited
master mode
User x has been added
to the system
User x has been removed
from the system
Master user changed
time and/or date
Master user cleared
faults
2-way transmission of
device is lost
2-way transmission of
device is restored
Dev x unsecured
(only when armed)
Dev x secured
(only when armed)
Cell radio fault
Cell radio cleared
Network control fault
(RF processor)
Network control cleared
Force disarm due to
low battery
Periodic call to
monitoring service
8-minute alarm
cycle complete
Action
Check for faults; resolve
issue, clear fault and
then re-arm
NA
Check for faults; resolve
issue, clear fault and
then re-arm
NA
Call customer service to
test system for issues
NA
NA
NA
NA
NA
NA
NA
NA
NA
Call customer service to
test system for issues
NA
Check dev x
NA
NA
NA
Fault will clear itself
NA
NA
NA
NA