Functional Description - Milwaukee FORCELOGIC M18 Manual Del Operador

unpredictable behavior resulting in fire, explosion or
risk of injury.
• Do not expose a battery pack or tool to fire or ex-
cessive temperature. Exposure to fire or temperature
above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging im-
properly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
SERVICE
• Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
• Never service damaged battery packs. Service of
battery packs should only be performed by the manu-
facturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
CABLE CUTTER
• Do not use tool without cutting jaws installed.
Fingers could be crushed.
• Blade is sharp. Keep hands away from all cutting
edges and moving parts. Laceration and amputation
can occur.
• To reduce the risk of injury, wear safety goggles or
glasses with side shields when operating or servic-
ing the tool. Material may crack or shatter.
• To reduce the risk of explosion,
WARNING
electric shock and property
damage, do not use on live electrical lines. Tool
is NOT insulated. Contact with a live circuit
could result in severe injury or death. Turn off power
before making a cut. Never cut gas or water lines.
• Maintain labels and nameplates. These carry im-
portant information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
•
Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
SPECIFICATIONS
Cat. No. ..................................................... 2672-20
Volts ...................................................................18 DC
Battery Type ..................................................... M18™
Charger Type ................................................... M18™
Jaw Type ..........................................477 ACSR Jaws
Maximum Capacity ...... ACSR: 477 MCM Hen ACSR
Replacement Blades .................. Cat. No. 48-44-0412
Jaw Type ..................................... 750 MCM Cu Jaws
Maximum Capacity ..............Copper Cable: 750 mcm
(Cat. No. 49-16-2773)
Guy Wire: 3/8" Non-EHS
Rebar: 3/8"
Ground Rod: 3/8"
(Cat. No. 49-16-2772)
Aluminum Cable: 1000 mcm*
Replacement Blades .................. Cat. No. 48-44-0411
* 750 MCM Cu Jaws will cut any aluminum cable with
a diameter less than 1.225"
Jaw Type ............................1/2" EHS Guy Wire Jaws
Maximum Capacity EHS Guy Wire: 1/2" (19 strand)**
Non-EHS Guy Wire: 1/2" (7 & 19 strand)**
Replacement Blades .................Cat. No. 48-44-2777
** May require two cutting cycles to complete cut on
1/2" wire
Jaw Type ........................... Fine Stranded Wire Jaws
Maximum Capacity ..................... Fine Stranded Wire:
Replacement Blades .................Cat. No. 48-44-2778
*** Jaws should only be used on the following wire
classes: M, K, I/DLO

FUNCTIONAL DESCRIPTION

1. Backup release valve
2. 750 MCM Cu jaws
3. Blades
4. Socket screws (5 mm)
2
3
4
5
6
5. Locking thumb
screw
6. Trigger
7. Handle
8. LEDs
9. ONE-KEY™
indicator
10. Hanger
11. 477 ACSR jaws
12. Blade retainer
13. Retaining pin
14.Fine stranded wire jaws
SYMBOLOGY
Volts
Direct Current
UL Listing for Canada and U.S.
US
C
WARNING
shock and property damage, do not
use on live electrical lines. Tool is
NOT insulated. Contact with a live
circuit could result in severe injury or
death. Turn off power before making a
cut. Never cut gas or water lines.
WARNING
moving parts. Blade is sharp. Laceration
and amputation can occur.
3
(Cat. No. 49-16-2777)
ACSR: 4/0 AWG
Rebar: 3/8"
Ground Rod: 3/8"
(Cat. No. 49-16-2778)
1/0 AWG - 777.7 AWG***
8
7
11
12 12
13
To reduce the risk of
explosion, electric
Keep hands away from
all cutting edges and
1
9
10
14
13