Safety Regulations - TMR TMR55 Manual De Uso

thus allowing you to paint with speed, precision and safety, bringing down costs and respecting the environment, with a limited
"fog effect". The machine can be combined with a great quantity of accessories; therefore it can be personalized according
to one's own use.
6 DESCRIPTIVE DRAWING (See the drawing A, page 3)
7 TECHNICAL TECHNICAL
The blowing unit is fed by a single-phase electric voltage between 220-230/240W and 50/60Hz. The fan coupled motor
generates an air flow which, canalized into the feed pipe, reaches the spray gun nozzle. The air flow rate can be adjusted
by means of the proper knob (on the models TMR80, TMR140, TMR90E, TMR150E and TMR180E) to optimize the
quantity and paint finishing of the covering product also according to its density/viscosity. The high volume at low
pressure provides the pulverization of the covering product and, wrapped at the same time by the air blast, deposits it in
a "soft" and precise way on the support which has to be painted. Therefore the system allows to prevent or restrict the "fog
effect", thus reducing the dispersal of the sprayed materials in the air. The performance is therefore improved, and this
also helps the operator's health and the environment. The machine also produces hot and dry air (by reducing the relative
humidity of about 40%), thus providing a better and faster drying of the material, especially in case of synthetic enamels.
All components are of high quality and purpose-made.
8 IDENTIFICATION
The manufacturer identification and CE conformity plate is placed on the front panel.
The plate must not be removed for any reason.
9 PAINTS, FLUIDS AND ADEQUATE PRODUCTS
Adequate products
Water-based or solvent-based paint
(enamels, antirust paints, primers, flatting varnishes,
etc.)
Wall paintings (tempera, water paints, multicolour
paints, fine quartz paints, etc.)
Plastic covering materials with granulometry of
Max. 3mm., which can be applied by means of a
spray gun MBL.
In order to obtain products with good features of mechanical resistance and resistance to the atmospheric agents, it is
necessary to follow the rules established by the manufacturer of the covering paints. Therefore prepare the products to be
used following the manufacturer's instructions.
10 DANGEROUS AND IMPROPER USES
Using the unit in a different way than indicated by the manufacturer could damage the equipment and endanger the
operator. The unit is not designed to use dangerous, explosive and/or toxic materials and herbicides.
Our company is not responsible for accidents deriving from the use of the machine by NOT TRAINED and not qualified
personnel, for aims different from the ones indicated above.

11 SAFETY REGULATIONS

Warning! Respect the following safety regulations for the use of electric tools in order to protect yourself against
electric shocks, dangers of lesions or fire.
Consider the working environment:
- Do not expose electric tools to rain and do not use them in moist or wet environments;
- Provide for a good lighting:
- Do not use electric tools in areas with risk of fire, near liquids or inflammable gases;
- Do not work in closed environments without an adequate change of air.
Protect yourself against electric shocks:
- Avoid the contact with grounded components (hoses, hot plates, refrigerators, electric heaters);
Keep the tools in a safe place:
- The tools not currently used must be put in a dry and well-sheltered place:
- Not trained people must keep away from the machine; above all, it cannot be placed in areas easily reachable by children;
Do not use the cables for aims different from the expected ones:
- Do not transport the tool by its cable and do not extract the plug by pulling the cable.
- Protect the cable against oil, acids, heat sources and sharp edges;
Take care of the tools:
- Keep the tools clean and always efficient by following the use and maintenance instructions;
- Check the plug, the cable and the switch periodically, and, in case of damages, they must be replaced by skilled personnel.
Net plug:
- In order to perform cleaning or maintenance operations always extract the net plug;
Avoid accidental starts:
- Never transport the tools connected to the net when your fingers or hands are on the switch;
Supply extension cable:
- In order to use it outdoors, use only type approved extension cables for external use, and replace them if they are damaged.
TMR55 TMR80 TMR140 TMR90E TMR150E TMR180E
✔ ✔ ✔
✔ ✔ ✔
✔
- 9 -
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
EN