Assembly; Navigator; Using The Vacuum; Emptying The Dust Cup Assembly - Shark NV105 Manual Del Usuario

Using the Vacuum

The height of your power nozzle has been
optimized for easy pushing and superior
cleaning on all floor types. There is no need
to make any height adjustments as you
transition to different floor & carpet types.
Fig. 7
Fig. 9
Fig. 8
IMPORTANT: To protect your
Your Shark ®

Navigator

™ can be
used to clean all surface types. carpets, the brushroll will only
turn on when you have pulled
1
Plug in the vacuum.
the handle back towards you
2 Push the "Power" button.
and released the power nozzle.
(Fig. 7)
IMPORTANT: The brushroll
3
Place your foot on the power
indicator light on the power
nozzle and pull the handle back
nozzle will illuminate solid red if
towards you. (Fig. 8)
there is a blockage. (Fig. 10) This
feature is designed to protect
NOTE: This vacuum has a
your Lifetime Belt that powers
separate "Brushroll" button on
your brushroll. See Checking
the top of the vacuum. (Fig. 9)
for Blockages on page 10.
4 CLEAN CARPETS:
5 CLEAN BARE FLOORS:
Engage the brushroll by pushing
For cleaning bare floors or to
the "Brushroll" button to the
clean with the hose, push the
"ON" position. The brushroll
"Brushroll" button to the "OFF"
light will turn green. (Fig. 9)
position for suction only. The
brushroll light will turn off. The
brushroll will not spin in this
mode.
6 TOLL FREE: 1-800-798-7398
Always hold the vacuum when using
the hose to clean so that it does not
tip over.
DO NOT pull vacuum cleaner around by
the hose.
DO NOT over-extend the hose.
Fig. 10
Indicator Light
Fig. 12
6
CLEAN ABOVE-FLOORS WITH
HOSE:
You can attach the accessories onto
the handle or onto the extension
wand for a longer reach.
a Stand the vacuum into upright
position.
b To remove the handle only, press
the handle release button.
(Fig. 11)
c
To remove the handle with
the extension wand, press the
extension wand release button
on the back of the vacuum.
(Fig. 12)
d Push the selected tool into the
end of the handle or handle with
extension wand for longer reach
and begin cleaning.
To order additional parts and accessories,
go to www.sharkclean.com.

Emptying the Dust Cup Assembly

For best results empty the Dust Cup Assembly after
each use; or as needed during prolonged usage. or
when it reaches the MAX fill line.
DO NOT OVERFILL.
Turn vacuum off before emptying.
Dust cup
Release
Button
Fig. 11
Fig. 13
TO EMPTY THE DUST CUP

ASSEMBLY:

1
Press the Dust Cup release
button ( )and remove the dust
cup from the vacuum. (Fig. 13)
2 Grip carry handle and press the
bottom Dust Cup Door release
button. (Fig. 14)
3
Option A: for Quick Empty:
Insert Dust Cup Assembly deep
inside trash receptacle to contain
dust and debris. (Fig. 15)
Press the bottom Dust Cup Door
release button; tap container
gently to dislodge and release
dust and debris.
Close the bottom door until it
snaps in place.
Important: If the Dust Cup
Door does not swing open freely
after pressing the release button,
push the door open using the
bottom door tabs.
Fig. 14
Fig. 15
Fig. 18
4
Option B: For Allergy Sufferers: Note: It may become necessary
Wrap a trash bag around the to occasionally clean the metal
Dust Cup Assembly leaving screen inside the dust cup. To
space at the bottom for the door clean, press the top dust cup
to swing open. (Fig. 16)
release button (Fig. 17), pull out
the metal screen and remove
Locate the Dust Cup Door
any excess dirt. Then replace the
release button within the trash
metal screeen inside the dust
bag and press to release as you
cup and close the top lid.
shake the dust cup to empty
(Fig. 18)
dust and debris.
Close the bottom door until it
snaps in place.
Note: Option B can also be
performed outside of the home
to further minimize releasing
dust back into the air. Carry just
the Dust Cup Assembly and trash
bag outside.
www.sharkclean.com
English
Fig. 16
Fig. 17
7