Machine-Specific Safety Warnings - Bosch 3 603 C98 0 Serie Instrucciones De Servicio

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21
OBJ_BUCH-2 609 000 792-001.book Page 2 Tuesday, February 7, 2006 9:59 AM
d) Store idle power tools out of the reach of
children and do not allow persons unfamil-
iar with the power tool or these instruc-
tions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tool's operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working con-
ditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous situ-
ation.
5) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Machine-specific
Safety Warnings
B When working with the machine, always hold
it firmly with both hands and provide for a
secure stance. The power tool is guided more
secure with both hands.
B Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
B Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
B Take protective measures when dust can
develop during working that is harmful to
one's health, combustible or explosive. Exam-
ple: Some dusts are regarded as carcinogenic.
Wear a dust mask and work with dust/chip extrac-
tion when connectable.
B Keep your workplace clean. Blends of materials
are particularly dangerous. Dust from light alloys
can burn or explode.
B Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over the
power tool.
2 609 000 792 • 7.2.06
B Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the
mains plug when the cable is damaged while
working. Damaged cables increase the risk of an
electric shock.
B Connect machines that are used in the open
via a residual current device (RCD).
B Keep hands away from the sawing range. Do
not reach under the workpiece. Contact with
the saw blade can lead to injuries.
B Apply the machine to the workpiece only
when switched on. Otherwise there is danger of
kickback when the cutting tool jams in the work-
piece.
B When the cut is completed, switch off the
machine and then pull the saw blade out of
the cut only after it has come to a standstill. In
this manner you can avoid kickback and can place
down the machine securely.
B Use only sharp, flawless saw blades. Bent or
unsharp saw blades can break or cause kickback.
B Do not brake the saw blade to a stop by apply-
ing side pressure after switching off. The saw
blade can be damaged, break or cause kickback.
B Clamp material well. Do not support the work-
piece with your hand or foot. Do not touch
objects or the floor with the the saw running.
Danger of kickback.
B Use suitable detectors to determine if utility
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pene-
trating a water line causes property damage or may
cause an electric shock.
B Hold the power tool only by the insulated
gripping surfaces when performing an opera-
tion where the cutting tool may contact hid-
den wiring or its own power cord. Contact with
a "live" wire will also make exposed metal parts of
the power tool "live" and shock the operator.
English–2

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pfz 500 e

Tabla de contenido