Maintenance And Inspection - Hitachi D 10YB Instrucciones De Manejo

CAUTION
Check and make sure positively that the switch is
off before inserting the plug into the power outlet.
Otherwise, a sudden start of the tool definitely
results an accident.
2. Pressing force of drill
You can not get holes quickly even if pressing it
by strong force more than necessary.
It not only damages the tip of drill bits and decreases
the efficiency of operation, but also shortens the
life of the drill.
3. When drilling completely through the material
When the drill bit bores completely through the
material, careless handling often results in a broken
drill bit or damage to the drill body itself due to
the sudden movement of the drill. Always be alert
and ready to release pushing force and hold the
drill body securely with both hands when drilling
through the material.
4. Adjusting the drilling speed
D10YB is equipped with electric control circuit which
enables non-step speed control.
To adjust the speed, turn the dial shown in Fig. 5.
When the dial is set to "1", the drilling speed is
minimum speed (500/min). When the dial is set to
"5", the drilling speed is maximum speed (2300/
min). Adjust the drilling speed according to the
material.
NOTE
When the dial is set to "1", there can be cases
where no rotation takes place due to a power
situation, etc. In this case, raise the dial slightly
before use.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits
Since use of an abraded drill bits will cause motor
malfunctioning and degraded efficiency, replace the
drill bits with a new one or resharpening without
delay when abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
4. Inspecting the carbon brushes (Fig. 7)
The motor employs carbon brushes which are
consumable parts. Since an excessively worn carbon
brush can result in motor trouble, replace the carbon
brushes with new ones which have the same carbon
brush No. shown in the figure when they become
worn to or near the "wear limit". In addition, always
keep carbon brushes clean and ensure that they
slide freely within the brush holders.
5. Replacing carbon brushes
Disassemble the brush caps with a slotted-head
screwdriver the carbon brushes can the be easily
removed.
6. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
GUARANTEE
We guarantee Hitachi Power Tools in accordance with
statutory/country specific regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling
instruction, to a Hitachi Authorized Service Center.
NOTE
Due to HITACHI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.
IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance
with the following code:
Blue: -Neutral
Brown: -Live
As the colours of the wires in the main lead of this
tool may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire coloured blue must be connected to the
terminal marked with the letter N or coloured black.
The wire coloured brown must be connected to the
terminal marked with the letter L or coloured red.
Neither core must be connected to the earth terminal.
NOTE
This requirement is provided according to BRITISH
STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be
applicable to other markets except The United Kingdom.
English
6