Additional Safety Instructions For Lawn Scarifiers & Rakers - IKRA IEVL 1738 Instrucciones De Manejo

f) Disconnect the power supply (e.g., pull the
plug from the mains socket) in the following
cases:
- every time you leave the device unattended;
- before removing blockages/obstructions of
the tool;
- before inspecting, cleaning or performing
any other works on the device;
- after an object got caught or hit.
g) Thoroughly read the "Rules for Safe Opera-
tion" of the device.
Recommendation
Only connect the device to a power source that is
protected via a residual current protective device
(RCD) with a maximum release current of 30 mA.
The use of an RCD or other circuit
breaker unit does not release the op-
erator of your Machine from the safety
instructions and safe working practic-
es given in this manual.
Additional safety instructions for lawn scari-
fiers & rakers
- The device is intended for private use only.
It must not be used in public gardens, parks,
sports facilities, grass verges, and professional
agriculture and forestry.
- A feeling of tingling or numbness in the hands
is an indicator for excessive vibration. Limit
operating times, make sufficiently long work
breaks, distribute the work with the device
among several persons, or wear anti-vibration
protection gloves when working with the de-
vice for longer periods of time.
- When working with the device, a certain level
of noise cannot be avoided. Noisy work should
be scheduled for hours, during which it is al-
lowed by statute or other local regulations. Ad-
here to any applicable rest times and limit your
working time to the necessary minimum time.
For your personal protection and the protection
of people nearby, suitable hearing protection
must be worn.
- Do not get distracted and always concentrate
on what you are doing. Use common sense.
Never operate the tool when you are tired, sick
or under the influence of alcohol or other drugs.
Additional general safety instructions
- Do not handle the plug or the tool with wet
hands and do not use the tool in the rain.
GB | Operating Instructions
- Use only outdoor rated extension leads that
- Use a power cable H05 RN-F or H05 VVF or
- Use a face mask if dusty.
- Keep clear of discharge openings at all times.
- Do not use solvents or cleaning liquids to clean
- Keep your working area clean and tidy. Untidy
- Do not operate the tool in potentially explosive
- Avoid physical contact with earthed surfaces
- Store power tools out of the reach of children.
- Do not overtax the power tool. Use the power
- Do not use the cable to carry or hang up the
- Do not overestimate your abilities. Take care
- Remove adjustment tools or wrenches and the
- Avoid unintentional operation. Make sure that
- Always pay attention to what you do and apply
- Thoroughly maintain your power tool. Check
GB-4
are so marked. Keep the extension cord away
from heat, oil and sharp edges.
greater, with minimum cross section of 2 x1.5
2
mm and max length of 20 m.
your Machine - use a blunt scraper to remove
grass and dirt. Always disconnect from the
electrical supply before cleaning.
and poorly lit working areas may lead to ac-
cidents.
environments containing combustible fluids,
gases or dusts.
as pipes, heaters, ovens and refrigerators.
Do not allow persons to use the tool if they are
not familiar with the tool or these instructions.
tool intended for your type of work in each case.
tool or to pull the plug out of the socket. Keep
the cable away from heat, oil and sharp edges
or moving parts of the tool. Damaged or tan-
gled cables increase the risk of electric shock.
of a safe footing and keep your balance at all
times.
like before you switch the tool on.
the switch is in 'OFF' position before pulling
the plug from the mains socket. When carrying
the tool with your finger on the on/off switch or
connecting the tool to the mains supply with
the switch in 'ON' position, this may result in
accidents.
reasonable care when working with a power
tool. Do not use the tool when you are tired
or under the influence of medication, drugs
or alcohol.
whether moving parts are working properly
and are not jamming/sticking, and whether
parts are broken or otherwise damaged in a