Special Safety Instructions - stayer FH230 Manual De Instrucciones

1. List of contents
2. Special safety instructions...................................15
3. Machine-specific Safety Warnings.......................17
3.1. Placing or fixing the tool........................................17
3.2. Assembling..........................................................17
3.3. Charger/battery...................................................18
3.4. Illustrated description of functions.........................18
4. Operating instructions..........................................18
4.1. Placement and testing..........................................18
4.2. Tool change..........................................................18
4.3. Limits on the size of workpiece..............................18
4.4. Instructions for use...............................................19
5. Maintenance instructions.....................................19
5.1. Cleaning, maintaining, lubricating, sharpening.....19
5.2. Repair service......................................................19
5.3. Guarantee............................................................19
5.4. Disposal...............................................................20
6. Legal Regulations.................................................20
6.1. Technical features................................................20
6.2. EC Declaration of Conformity...............................20
The machine is intended for cutting, roughing, and
brushing metal and stone materials without using water.
With approved sanding tools, the machine can be used
for sanding with sanding discs.
2. Machine-specific Safety Warnings
Safety Warnings Common for Grinding,
!
Sanding, Wire Brushing or Abrasive
Cutting-Off Operations
This power tool is intended to function as a grinder,
sander, wire brush or cut-off tool. Read all safety
w a r n i n g s , i n s t r u c t i o n s , i l l u s t r a t i o n s a n d
specifications provided with this power tool. Failure
to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
This power tool is not recommended for polishing.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
ENGLISH
15
The arbor size of wheels, flanges, backing pads or any
other accessory must properly fit the spindle of the
Page
power tool. Accessories with arbor holes that do not
match the mounting hardware of the power tool will run out
of balance, vibrate excessively and may cause loss of
control.
Do not use a damaged accessory. Before each use,
inspect the accessory such as abrasive wheels for
chips and cracks, backing pads for cracks, tears or
excess wear, wire brushes for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying debris
generated by various operations. The dust mask or
respirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
Keep bystanders a safe distance away from the work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Contact with a "live" wire will also make
exposed metal parts of the power tool "live" and shock the
operator.
Position the cord clear of the spinning accessory. If
you lose control of the power tool, the cord may be cut or
snagged and your hand or arm may be pulled into the
spinning accessory.
Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your control.
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
Regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
15