Back Panel Description; Speaker Outputs; Inputs; Input Mode Switch - D.A.S. energy Serie Manual De Usuario

BACK PANEL DESCRIPTION

A) Speaker outputs
Terminal connectors are provided to connect
the speakers. Both 70V and 100V connections are
available. More examples on Appendix D.
B) Inputs
An XLR input is connected in parallel to an
Jack for each amplifier. For more information
consult Appendix B.
Nominal input impedance is 20 Kohm for
balanced use and 10 Kohm for unbalanced use.
Polarity complies with AES14-1992 (ANSI
S4.48-1992) and therefore pin assignments are:
Pin 1 (XLR) or Sleeve (Jack).- GND (Ground).
Pin 2 (XLR) or Top
signal.
EN
Pin 3 (XLR) or Ring
4
SPEAKER
OUTPUT
CHANNEL A
0 0
70V
BRIDGE
70 70
1 00V
25V
100 100
1 40V 200V
100 100
25V
70 70
1 00V
70V
0 0
CHANNEL B

Speaker outputs

E A
(Jack) .- (+) Non
(Jack) .- (–) Inverted signal.
HOT
2
COLD
3
1
GND
HOT COLD
GND
Manual del Usuario
CHANNEL B
XLR and Jack 6.35mm (1/4") inputs
CAUTION ATTENTION
RISK OF ELECTRIC SHOCK DANGER D'ELECTROCUTION
DO NOT OPEN NE PAS OUVRIR
Serial Number:
CHANNEL B CHANNEL A
D.A.S. AUDIO S.A. (Valencia) SPAIN
SPEAKER OUTPUT
CHANNEL A
SIGNAL
0
INPUT
BRIDGE
70V
70 1 00V
25V
100
1 40V 200V
1 2 3 4 5 6 7 8 91 0 1 1 1 2
ON
100
OFF
25V
70
1 00V
70V
0
WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK
CHANNEL B
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
VER MANUAL DE INSTRUCCIONES PARA LA CONEXIÓN
N1918
REFER TO INSTRUCTIONS MANUAL FOR CONNECTION
EUROPEAN
ANSCHLUSSWEISE BITTE DER ANLEITUNG ENTNEHMEN
PRODUCT
MADE IN SPAIN
VOIR MANUEL D'INSTRUCTIONS POUR LA CONNEXION
B C D
C) Input mode switch
This multi-switch allows the selection for the
input configuration mode: stereo, parallel or
bridge.
Typically the amplifiers are used in stereo
mode, where the input to channel A feeds channel
A and the input to channel B feeds channel B.
Parallel mode allows feeding both channels
with the signal plugged into channel A. Channel
B's input is disconnected in this mode.
Use the Bridge mode to use the power of both
amplifiers for one single output. For more
information consult Appendix A.
In the upper figure, the Input Mode Switch can
be seen located between the two XLR input
connectors.
inverted
D) Power cord
The amplifier is plugged into the mains by way
of a power cord with three isolated cables, color
code being brown (live), blue (neutral) and yellow-
green (earth). It may be that the color code is not
the same in each country.
E) Fan inlet grilles
Like for the front outlet grilles, keep clean and
dust-free to assure free air intake for proper
cooling.
/ energy /
User's Manual
CAUTION ATTENTION
RISK OF ELECTRIC SHOCK DANGER D'ELECTROCUTION
DO NOT OPEN NE PAS OUVRIR
CHANNEL A
SIGNAL
INPUT
1 2 3 4 5 6 7 8 91 0 1 1 1 2
ON
OFF
WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE
VER MANUAL DE INSTRUCCIONES PARA LA CONEXIÓN
REFER TO INSTRUCTIONS MANUAL FOR CONNECTION
ANSCHLUSSWEISE BITTE DER ANLEITUNG ENTNEHMEN
VOIR MANUEL D'INSTRUCTIONS POUR LA CONNEXION
E