Noise/Vibration Information; Charging The Battery (See Figure B); Inserting/Changing The Saw Blade - Bosch AdvancedRecip 18 Manual Original

14 | English
Reciprocating saw
Tool holder
Stroke
Max. cutting depth
– in wood
– in steel (unalloyed)
– Pipe diameter
Weight according to
EPTA-Procedure 01:2014
Weight with 2.5 Ah battery
(PBA 18 2,5 Ah) according
to EPTA-Procedure
01:2014
Permitted ambient temperature
– during charging
A)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Limited performance at temperatures <0 °C

Noise/vibration information

Noise emission values determined according to
EN 62841-2-11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 86 dB(A); sound power level
97 dB(A). Uncertainty K=5 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-11:
Cutting boards with saw blade S 3456 XF:
2 2
a =10 m/s , K=1.5 m/s ;
h,B
Cutting wooden beams with saw blade S 3456 XF:
2 2
a =10.5 m/s , K=1.5 m/s .
h,WB
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure detailed in EN 62841
and may be used to com-pare power tools. They may also be
used for a preliminary estimation of vibration and noise
emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
1 609 92A 4JX | (01.10.2018)
Implement additional safety measures to protect the oper-
AdvancedRecip 18
ator from the effects of vibration, such as servicing the
SDS
power tool and application tools, keeping their hands warm,
mm 23
and organising workflows correctly.
Fitting
mm 100
mm 20
u
mm 20
kg 2.1
kg 2.5
Charging the battery (see figure B)
u
°C 0 to +45
Note: The battery is supplied partially charged. To ensure
°C −20 to +50
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
PBA 18V...V -.
reducing its service life. Interrupting the charging process
PBA 18V...W-.
does not damage the battery.
AL 22.. CV
The lithium-ion battery is protected against deep discharge
AL 18.. CV
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
To remove the battery (8), press the release button (10)
and pull the battery back and out of the power tool. Do not
use force to do this.
Battery charge-control indicator
When the on/off switch (6) is pressed in halfway or com-
pletely, the battery charge indicator (5) indicates the bat-
tery's state of charge for several seconds. The indicator con-
sists of three green LEDs.
LED
Continuous light 3 x green
Continuous light 2 x green
Continuous light 1 x green
Slowly flashing light 1 x green
The 3 LEDs in the battery charge indicator (5) flash quickly if
the temperature of the battery is above the permitted oper-
ating temperature range.

Inserting/changing the saw blade

u
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
When fitting or changing the saw blade, wear protect-
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
While replacing the saw blade, ensure that the saw
blade receptacle is free of material residue, e.g. wood
or metal chips.
Capacity
> 66%
33–66%
11–33%
<11%
Bosch Power Tools