Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Ordering Replacement Parts; Disposal And Recycling - EINHELL GC-RT 1545 M Manual De Instrucciones

the end of the area you wished to hoe. The motor
must be switched off when you raise the machine
(for example to change direction).
Keep the underside of the machine clean and re-
move soil deposits. Deposits make it more diffi cult
to start the machine and decrease the working
depth. Work perpendicular to the slop on inclined
areas. The machine must be switched off and the
mains cable disconnected before you make any
checks on the hoe blades.
Warning!
The hoe blades will continue to rotate for a few
seconds after the motor is switched off . Never att-
empt to manually stop them. In the event that the
rotating hoe blade strikes an object, immediately
switch off the machine and wait for the hoe blades
to come to a complete stop. Then inspect the con-
dition of the hoe blades. Replace any parts that
are damaged.
Lay the power cable on the ground in front of the
outlet in a fi gure 8. Work away from the outlet or
cable and ensure that the power cable always
trails in the hoed soil which will prevent the hoe
blades from traveling over the cable.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Maintenance and cleaning work on the machine
as well as removal of the safety devices may only
be performed when the motor is switched off and
the power cable has been pulled.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
Anl_GC-RT_1545_SPK9.indb 19 Anl_GC-RT_1545_SPK9.indb 19
GB
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Replace the hoe blades
For safety reasons, we recommend having the
hoe blades replaced by an authorized professio-
nal (see address on warranty certifi cate).
Wear working gloves. Use only genuine spare
parts since otherwise the function and safety of
the machine cannot be guaranteed.
8.3 Maintenance
Ensure that all mounting components (i.e. screws,
bolts, nuts etc.) are always tightened so that the
machine can be safely operated at all times.
Store the device in a dry room. All the metal parts
should be cleaned and then oil to ensure that
they provide a long life. For best results, clean the
plastic parts of the machine with a brush or rag.
Do not use any solvents to remove dirt.
For space saving storage undo the star nuts (Fig.
12/Item 8) and fold together the push bars as
shown in Fig. 12. Ensure that you do not damage
the cable. At the end of the season, perform a
general inspection of the machine and remove
any deposits which may have accumulated. At the
start of each season, ensure that you check the
condition of the machine. If repairs are necessary,
please contact one of our customer service cen-
ters (see address on warranty certifi cate).

8.4 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com

9. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
- 19 -
10.09.2020 13:55:04 10.09.2020 13:55:04