Removing/Inserting The Battery - Milwaukee REDSTICK MLDIG14 Manual Del Operador

To reduce the risk of injury or explo-
WARNING
sion, never burn or incinerate a
battery pack even if it is damaged, dead or com-
pletely discharged. When burned, toxic fumes and
materials are created.
Disposing of MILWAUKEE Li-Ion Battery
MILWAUKEE Li-Ion batteries are more environmen-
tally friendly than some other types of power tool
batteries. Always dispose of your battery according
to federal, state and local regulations. Contact a
recycling agency in your area for recycling locations.
Even discharged batteries contain some energy.
Before disposing, use electrical tape to cover the
terminals to prevent the battery from shorting, which
could cause a fire or explosion.
RBRC Battery Recycling Seals
The RBRC™ Battery Recycling Seals (see "Symbol-
ogy") on your batteries indicate that MILWAUKEE
has arranged for the recycling of that battery with
the Rechargeable Battery Recycling Corporation
(RBRC). At the end of your battery's useful life,
return the battery to a MILWAUKEE Branch Office/
Service Center or the participating retailer nearest
you. For more information, visit the RBRC web site
at www.rbrc.org.
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, unlatch the
battery door. Turn the level over
and let the battery slide out from
the tool.
To insert the battery, slide the pack into the body of
the tool by aligning the white arrow on the battery
with the white arrow on the battery compartment.
Close the battery door.
NOTE: The battery, once removed, may be charged
in the REDLITHIUM® USB Charger, model 48-59-
2002. Alternatively, see "Charging the Battery",
below, for charging without removing from the level.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Charging the Battery
1. Plug your USB cable into a power source such as
an AC wall adaptor, computer or car port. Charge
rates may vary depending on the power source's
maximum output.
2. Lift the rubber cover to expose the micro USB port.
Insert the micro USB plug into the micro USB port.
3. The indicator light will display the charging status:
Red Solid: Charging, 0-79% charged
Green Flashing: Charging, 80-99% charged
Green Solid: 100% Charged
Red/Green Flashing: Damaged or Faulty Battery
LEVEL
If the light indicator flashes red and green, check
that the battery is fully seated into the bay. Remove
the battery and reinsert. If the light continues
to flash red and green, the battery may be ex-
tremely hot or cold, or wet. Allow the battery to
cool down, warm up, or dry out and then reinsert.
If the problem persists, contact a MILWAUKEE
service facility.
NOTE: The level will not be able to be used while
the battery is charging.
Turning ON/OFF
Press and hold the power button
on and off. The level will beep to indicate it is ready.
Audio Leveling
Double tap the power button
or off. This feature can also be accessed by pressing
the menu button
When on, the level will sound when it is within 10°
of the target. The beats per minute will change once
you are within 5°. If the target is crossed, the pitch
will also change, indicating a passed target.
When a target is reached within the tolerance range
set by the user, the on target tone will play.
Menu Guide
Press the menu button
Once open, press the menu button
cycle through the menu screens and the up and down
arrow keys to modify settings.
To exit, select exit on the menu screen or press and
hold the menu button
Description Function
Mode Changes the level's measurement
type between angle, percent,
in/ft, and mm/m
Sensitivity Changes the precision of the
mode selected between whole,
tenth, and hundredth
Tolerance A d j u s t s t h e s t a r t o f c o l o r
activation as the level approaches
the desired target
Sound Turns sound on or off
Settings Expands to more menus and
offers and exit to working mode
Power Mode Changes the display between
High Contrast, Auto and Power
Save
Language Changes the language settings
between English, French, and
Spanish
4
to turn the level
to turn the sound on
and cycling to Sound.
to access the menu.
.
again to