Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
1.5 GASES AND FUMES
PLEASE NOTE! GAS MAY BE LETHAL OR DANGEROUS TO HUMAN HEALTH!
•
Always stay clear of the gas exhaust.
•
Ensure proper ventilation of the work space and avoid gas inhalation.
•
Chemical substances (lubricants, solvents) must be removed from the surfaces of welded details as they
burn and emit toxic smokes under the influence of temperature.
•
Welding galvanised details is permitted only when efficient ventilation is provided with filtration and
access to fresh air. Zinc fumes are highly toxic, an intoxication symptom is so-called metal fever.
2. TECHNICAL DETAILS
Product name
Model
Article number
Voltage / frequency
Rated input current
No-load voltage
Welding current (MMA/MIG)
Duty cycle (MMA/MIG)
Welding current at 100% duty cycle (MMA/
MIG)
Wire diameter
Wire type
3. CONNECTION OF THE DEVICE
3.1 GENERAL NOTES
•
The device must be used according to its purpose, with observance of OHS regulations and restrictions
resulting from data included in the rating plate (IP level, operation cycle, supply voltage, etc.).
•
The machine must not be opened as it will cause warranty loss and, in addition, exploding, unshielded
elements can cause serious injuries.
•
The producer does not bear any responsibility for technical changes in the device or material losses
caused by the introduction of the said changes.
•
In case of incorrect device operation, contact the service centre.
•
Louvers must not be shielded - the welder must be positioned at 30 cm distance from objects
surrounding it.
•
The welder must not be kept under your arm or near to your body.
•
The machine must not be installed in rooms with aggressive environments, high dustiness and near
devices with high electromagnetic field emission.
3.2 DEVICE STORAGE
•
The machine must be protected against water and moisture.
•
The welder must not be positioned on heated surfaces.
•
The device must be stored in a dry and clean room.
EN
Welding Machine
S-MIGMA-155
S-MIGMA-175
S-MIGMA-195
2204
2205
2206
230 V~ / 50Hz
13 A (MMA)
14 A (MMA)
16 A (MMA)
11 A (MIG)
11,5 A (MIG)
14 A (MIG)
22-36 V
22-38 V
22-39 V
60-155 A
60-175 A
70-195 A
15 %
15 %
15 %
60 A
67 A
75 A
0,6 – 0,8 mm
0,6 – 0,8 mm
0,6 – 0,8 mm
Full / core
Full / core
Full / core
(FLUX)
(FLUX)
(FLUX)
12
Rev. 23.11.2016
3.3 CONNECTING THE DEVICE
3.3.1 CONNECTING THE POWER
•
Connection of the device must be performed by a qualified person. In addition, a person with required
qualifications should check if the earthing or electrical installation with protection system is in line with
the safety regulations and if they operate correctly.
•
The device must be placed near the work station.
•
Connection of excessively long conduits to the machine must be avoided.
•
One-phase welders should be connected to a socket fitted with an earthing prong.
•
Welders powered from a 3-Phase network are delivered without a plug, the plug must be obtained
independently and installation should be assigned to a qualified person.
PLEASE NOTE! THE DEVICE MAY ONLY BE USED UPON CONNECTION TO AN INSTALLMENT WITH
A PROPERLY FUNCTIONING FUSE
3.3.2 CONNECTING GAS
•
Gas tanks must be placed far from the welded object and be protected against falling.
•
Gas connector of the welder must be connected with the tank or gas installation by means of the
correct pipe and regulator with gas flow regulation. Please note! Connection of line regulators to the
tank and the other way round is prohibited. Such a change can result in regulator damage and serious
injuries.
•
Economical gas use extends the welding time
4. OPERATION
S-MIGMA-155:
6
5
4
3
7
2
8
9
1
10
1.
Power cord
2.
Wire feed rate adjustment knob
3.
On/off switch
4.
Welding current adjustment switch
5.
Operation mode switch MIG / MMA
6.
MIG cable
Rev. 23.11.2016
EN
S-MIGMA-175 | S-MIGMA-195:
7
2
8
6
5
3
9
10
1
13
Publicidad
Tabla de contenido
