OHAUS Explorer Pro Manual De Instrucciones página 20

Explorer Pro
3.4.1 Unidad de cliente (cont.)
MAIN MENU
CHANGE UNITS
GRAINS SELECT CUSTOM UNIT
HONG KONG TAELS
CUSTOM UNIT 1
SINGAPORE TAELS
CHANGE UNITS
CHANGE MODE
CUSTOM UNIT 2
ROC TAELS
CUSTOM UNIT 3
MOMMES
EXIT TO WEIGH
POUNDS
CHANGE UNITS
NEWTONS
GRAINS SELECT CUSTOM UNIT
TICALS
CUSTOM MENU CALIBRATION
HONG KONG TAELS
CUSTOM UNIT 1 CUSTOM UNITS
CUSTOM UNITS
SINGAPORE TAELS
CHANGE MODE
CUSTOM UNIT 2 RUN
EXIT TO WEIGH
ROC TAELS
CUSTOM UNIT 3
SETUP
MOMMES
EXIT TO WEIGH EXIT TO WEIGH
POUNDS
NEWTONS
TICALS
CUSTOM MENU
GRAINS
CUSTOM UNITS
HONG KONG TAELS
CUSTOM UNIT 1
EXIT TO WEIGH
SINGAPORE TAELS
CHANGE MODE
CUSTOM UNIT 2 RUN
ROC TAELS
CUSTOM UNIT 3 SETUP
MOMMES
EXIT TO WEIGH EXIT TO WEIGH
POUNDS
NEWTONS
TICALS
CUSTOM MENU
CUSTOM UNITS
EXIT TO WEIGH
CHANGE MODE
MAIN MENU
CHANGE UNITS
GRAINS SELECT CUSTOM UNIT
HONG KONG TAELS
CUSTOM UNIT 1 CUSTOM UNITS
SINGAPORE TAELS
CHANGE MODE CHANGE UNITS
CUSTOM UNIT 2 RUN
CUSTOM UNIT SETUP
ROC TAELS
CUSTOM UNIT 3
SETUP
UNIT NAME
MOMMES
EXIT TO WEIGH EXIT TO WEIGH
SET MANTISSA
POUNDS
SELECT DP
NEWTONS
SELECT LSD
CHANGE UNITS
TICALS
CUSTOM MENU CALIBRATION
SAVE & EXIT
CUSTOM UNITS
GRAINS SELECT CUSTOM UNIT
EXIT TO WEIGH
EXIT TO WEIGH
HONG KONG TAELS
CUSTOM UNIT 1
SINGAPORE TAELS
CHANGE MODE
CUSTOM UNIT 2 RUN
CUSTOM UNIT SETUP
ROC TAELS
CUSTOM UNIT 3 SETUP
UNIT NAME
MOMMES
EXIT TO WEIGH EXIT TO WEIGH
SET MANTISSA
POUNDS
SELECT DP
<UP>/<DOWN> TO SCROLL CHARACTERS
NEWTONS
SELECT LSD
<LEFT>/<RIGHT> TO MOVE CURSOR
TICALS
CUSTOM MENU
SAVE & EXIT
<ENTER> TO ACCEPT
CUSTOM UNITS
GRAINS
EXIT TO WEIGH
<BACK> TO ABORT
EXIT TO WEIGH
HONG KONG TAELS
CUSTOM UNIT 1
SINGAPORE TAELS
CHANGE MODE
CUSTOM UNIT 2
ROC TAELS
CUSTOM UNIT 3
MOMMES
EXIT TO WEIGH
POUNDS
NEWTONS
TICALS
CUSTOM MENU
CUSTOM UNITS
EXIT TO WEIGH
CHANGE MODE
SET BALANCE
MAIN MENU
LIBRARY
CHANGE UNITS SET BALANCE
MAIN MENU
CHANGE UNITS
LIBRARY
CALIBRATION
SELECT CUSTOM UNIT
CUSTOM UNITS
CHANGE UNITS SET BALANCE
CUSTOM UNIT SETUP
UNIT NAME
SET MANTISSA
SELECT DP
MAIN MENU
CHANGE UNITS
SELECT LSD
LIBRARY
CALIBRATION
GRAINS SELECT CUSTOM UNIT
SAVE & EXIT
HONG KONG TAELS
EXIT TO WEIGH
CUSTOM UNIT 1 CUSTOM UNITS
SINGAPORE TAELS
CHANGE UNITS
CUSTOM UNIT 2 RUN
CUSTOM UNIT SETUP
ROC TAELS
CUSTOM UNIT 3 SETUP UNIT NAME
UNIT NAME
MOMMES
EXIT TO WEIGH EXIT TO WEIGH
SET MANTISSA
-
POUNDS
SELECT DP
<UP>/<DOWN> TO SCROLL CHARACTERS
NEWTONS
SELECT LSD
<LEFT>/<RIGHT> TO MOVE CURSOR
TICALS
CALIBRATION
CUSTOM MENU
SAVE & EXIT
<ENTER> TO ACCEPT
CUSTOM UNITS
EXIT TO WEIGH
<BACK> TO QUIT
EXIT TO WEIGH
SET BALANCE
MAIN MENU
LIBRARY
CUSTOM UNITS
CHANGE UNITS
SET BALANCE
SET MANTISSA
-
MAIN MENU
CHANGE UNITS
LIBRARY
CALIBRATION
SELECT CUSTOM UNIT
CUSTOM UNITS
CHANGE UNITS SET BALANCE
RUN
CUSTOM UNIT SETUP
SETUP
UNIT NAME
EXIT TO WEIGH
SET MANTISSA
SELECT DP
SELECT LSD
CALIBRATION
SAVE & EXIT
MAIN MENU
CHANGE UNITS
EXIT TO WEIGH
GRAINS SELECT CUSTOM UNIT
HONG KONG TAELS
CUSTOM UNIT 1 CUSTOM UNITS
SINGAPORE TAELS
CHANGE UNITS
CUSTOM UNIT 2 RUN
SELECT DP LOCATION
ROC TAELS
CUSTOM UNIT 3
SETUP
E-3
MOMMES
EXIT TO WEIGH EXIT TO WEIGH
E-2
POUNDS
E-1
NEWTONS
E0
TICALS
CALIBRATION
CUSTOM MENU
E1
CUSTOM UNITS
E2
EXIT TO WEIGH
E3
Procedimiento (cont.)
• Pulse tecla de flecha
CUSTOM UNIT 1.
• Pulse la tecla Enter. El indicador señala CUSTOM UNITS.
Ahora puede Vd.elegir entre iniciar el programa, si antes
ha introducido datos, ajustar la unidad libre, o salir del
modo pesada. Este procedimiento sigue con el ajuste de
la unidad libre.
• Pulse la tecla de flecha
SETUP.
• Pulse la tecla Enter, aparece CUSTOM UNIT SETUP.
SET BALANCE
• Pulse la tecla de flecha
NAME.
LIBRARY
• Pulse la tecla Enter, aparece UNIT NAME.
• Usando las teclas de flecha, introduzca nombre de la
unidad, pulse Enter.
• Pulse la tecla de flecha
MANTISSA.
• Pulse la tecla Enter, aparece SET MANTISSA. Aparece la
mantisa del factor de conversión actual. Este es un número
entre 0.1 y 1.999999 con el primer dígito parpadeando.
Para factores de conversión fuera de este intervalo se usará
el exponente para mover el punto decimal.
• Con las teclas de flecha, introduzca factor de conversión,
pulse Enter, aparece CUSTOM UNIT SETUP.
• Pulse la tecla de flecha
SELECT DP.
• Pulse tecla Enter, aparece SELECT DP LOCATION.
LIBRARY
• Pulse la tecla
SET BALANCE exponente E-3, E-2, E-1, E0, E1, E2, ó E3.
• Pulse la tecla Enter, aparece CUSTOM UNIT SETUP.
LIBRARY
14
ó para seleccionar
ó para seleccionar
ó para seleccionar UNIT
ó para seleccionar SET
ó para seleccionar
ó para seleccionar valor de