Wahl 1885 Manual De Uso página 12

ENGLISH
Operation
de
Preparation
Keep the packaging material for safe storage or
transport later.
en
f Check that the delivery is complete.
f Check all the parts for possible transport damage.
fr
Safety
it
Handle with care! Damage due to incorrect power
supply.
f Only operate the appliance with an alternating cur-
es
rent and with the voltage stated on the nameplate.
Charging the battery
pt
1. Connect the appliance plug (Q) on the plug-in transformer
to the charging stand socket (Fig. 4ⓐ).
nl
· The appliance can also be connected directly to
the plug-in transformer for charging (Fig. 2ⓐ/ⓑ).
· Battery overcharging is prevented thanks to intel-
sv
ligent charge management.
2. Connect the plug-in transformer to the mains socket
no
(Fig. 4ⓑ).
3. Switch off the appliance using the on/off switch (Fig. 3).
4. Place appliance in the charging stand (Fig. 4) or connect
fi
directly to the plug-in transformer (Abb. 2ⓐ/ⓑ).
· During the charging operation, the LED on the on/
tr
off switch flashes. The charge status of the battery
is indicated by the colour of the on/off switch (C).
Red
pl
Orange = 25% – 50%
Green = 50% – 100%
· After the device has been removed from the
cs
charging stand, the display goes out after approx.
15 seconds (power saving mode).
It takes no more than 45 minutes for the appli-
·
sk
ance to charge to full capacity.
Battery operation
hu
1. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3).
sl
· After the appliance has been switched off, the
display goes out about 15 seconds later (power
saving mode).
ro
· When the battery is fully charged, the appliance
can be used for up to 90 minutes without mains
connection.
bg
· The charge status of the battery is indicated by
the colour of the on/off switch (C).
green = 100% – 50%
ru
orange = 50% – 25%
red
· When the battery has fully run down, the appli-
uk
ance switches itself off automatically.
· In case of insufficient maintenance of the
blade set, the operating time can be reduced
el
considerably.
ar
12
= 0% – 25%
= 25% – 0%
Mains operation
1. Connect the appliance plug (Q) on the plug-in transformer
to the appliance socket (F) (Fig. 2ⓐ).
2. Connect the plug-in transformer to the mains socket
(Fig. 2ⓑ).
3. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3).
Operation
Setting the cutting length
The cutting length can be adjusted to between 0.7 mm and 3
mm (5 possible positions) using the cutting-length adjustment
integrated into the blade set (Fig. 5).
f To do this, set the lever to the desired position and let it
snap into place.
Cutting with the attachment comb
The appliance can also be operated with attachment combs.
In order to achieve the indicated cutting length, the cutting
length adjustment lever should be set to position 1 (Fig. 5).
The following attachment combs are included as stan-
dard: 3 mm, 6 mm, 9 mm, 12 mm, 18 mm and 25 mm
cutting lengths.
Attaching/removing the attachment comb
1. Slide the attachment comb on to the blade set in the direc-
tion of the arrow until it reaches the limit stop (Fig. 6ⓐ).
2. The attachment comb can be removed by pushing it in the
direction of the arrow (Fig. 6ⓑ).
Attaching/removing the scissor handle
1. Press the release button (E) for the scissor handle
(Fig. 7ⓐ).
2. Let the scissor handle swing out in the direction of the arrow
(Fig. 7ⓑ) and remove the scissor handle from its holding
fixture (Fig. 7ⓒ).
3. To reinstall the scissor handle, carry out steps 1 and 2 in
reverse order.