Technical Data; Wall Mounting - Tecomec Jolly EVO Manual De Instrucciones

4. USING AND KEEPING UP THE OWNER'S MANUAL
The characteristics and the information given in this manual are merely indicative. The
manufacturer reserves the right to add any modifications to the grinder considered
necessary at any time.
It is forbidden to reproduce any part of this document without authorization on behalf
of the manufacturer.
The owner's manual is integral part of the appliance and must be kept in a safe place
so that it can be consulted whenever need be.
If you should loose your manual or it should deteriorate, you can request your dealer
or an authorized service centre for another copy.
The manual shall accompany the appliance at all times, especially if it is sold on at
a later date.
5. DEFINITIONS
Skilled technician: a person who is generally employed by the service centre and who
is trained to carry out extraordinary maintenance jobs and repairs on the appliance.
6. SYMBOLS
This symbol points out the possibility of serious personal injuries if the
provisions and instructions are not complied with.
This symbol points out that the user must wear protection goggles when
he uses the appliance.
This symbol points out that the user must wear protective gloves when
he uses the appliance.
This symbol points out the correct running direction of the appliance
(grinding wheel).
Read the instructions before using the machine
This symbol (on the rating nameplate) points out that the product
must not be disposed of with normal household garbage. Contact an
authorized shop or your dealer for disposal instructions.

7. TECHNICAL DATA

Model
Voltage
Rated power
Grinding wheel dimensions
Maximum speed of grinding wheel
Max. power of lamp
Acoustic pressure level
Acoustic power level
Level of vibrations on operating
handle (*)
Types of chains that can be
sharpened
Weight (complete machine)
(*) - The declared vibration total value has been measured in accordance with a
standard test method and may be used for comparing one tool with another.
- The declared vibration total value may also be used in a preliminary
assessment of exposure.
- While the electrical appliance is being used, the vibration emission
value may vary from the stated value depending on how the
appliance is used;
- Keep any stress caused by vibrations as low as possible.
A few hints to reduce stress induced by vibrations are: wear
gloves while using the appliance and work for short periods of
time. By doing this, consider every component of the work cycle
(for example, the moments when the appliance is switched off and
moments when even though it is switched on, it is idling).
( ** ) Only with specific kit (vise+grinding wheel 8 mm) to be ordered separately
8. PART DESCRIPTION (FIG.1)
1 Base unit
2 Arm-motor unit
3 Vise assembly
4 Chain blocking handle
5 Vise adjustment knob
6 Chain jaws
7 Chain blocking unit adjustment knob
8 Chain blocking unit adjustment knob
9 Chain blocking unit
Jolly EVO
230V~ 50Hz
220W
Outside Ø 145 mm - Inside Ø 22,2 mm
Thickness: 3.2 - 4.7 - 6.0 mm
-1
2700 min
0,5W
LpA:45,7dB(A),K=3dB(A)
LwA:58,7dB(A),K=3dB(A)
2
< 2,5 m/s
1/4" - .325" - 3/8" - .404" - 3/4"( ** )
6,3 kg
10 Arm-locking knob
11 Arm operating handle
12 Shield guard
14 Grinding wheel
15 Sharpening depth adjustment knob
17 Lamp (LED)
18 Main ON/OFF switch
19 Electrical power cable
20 Rating nameplate
EN
9. SAFETY DEVICES
The grinder is equipped with the safety devices illustrated hereafter:
- Shield guards: they protect the operator from parts of the grinding wheel that may
come away during the sharpening process.
These guards must always be fitted in place when the appliance is in use.
Always make sure the guards are efficient and fitted properly. Operator safety could
be compromised if the guards are damaged and/or cracked.
- Switch: the appliance features a safety switch with release coil. In the case of a
sudden power failure, the switch trips automatically and disconnects the appliance
from the mains. The appliance will not start even if the power supply is suddenly
restored. You need to reset the switch to start the appliance again.
10. INTENDED USE
This appliance is an electrical grinder for chains used in chain saws.
- Use the appliance exclusively for the types of chains stated in the technical data
chart.
- Do not use the appliance to cut or grind anything other than the chains envisaged.
- Secure the appliance firmly to the bench or wall.
- The appliance must not be used in corrosive or explosive environments.
- Any other use is to be considered improper.
The manufacturer is not liable for damages following improper or incorrect use of
the appliance.
11. UNPACKING
The grinder is supplied already partially assembled.
12. STANDARD SUPPLY (FIG.2)
1 - Base unit
2 - Arm-motor unit
3 - Owner's manual
4 - Test card
6 - Grinding wheel Ø 145x3.2x22.2 19 - Sharpening template
7 - Grinding wheel Ø 145x4.7x22.2 20 - Dressing brick
8 - Grinding wheel Ø 145x6x22.2
12 - Arm securing screw M10
13 - Washer for screw M10
13. TESTING THE GRINDING WHEEL
Hold the grinding wheel up by its central hole. Knock the edge of the grinding
wheel (fig.3) gently with a non-metallic object. If it makes a numb non-metallic noise
it means that the wheel could be damaged: do NOT use it!
14. INSTALLATION
ATTENTION
Do not install the machine at eye level. You are recommended to install it at a height
of no more than 1.2-1.3 meters off the floor.
The machine can be bench mounted or wall mounted.
14.1 BENCH MOUNTING
- Fitting the arm (fig.4): to secure the arm-motor unit to the base unit, insert the V5
screw in the dedicated hole F5. Insert the washer R5 and tighten the knob M23.
- Securing the base unit (fig.5): use 2 M8 screws complete with washers and nuts
(material not supplied), inserted in the securing holes F4. Make sure you position
the base unit on the bench as illustrated in the detail.

14.2 WALL MOUNTING

- Fitting the arm (fig.4): to secure the arm-motor unit to the base unit, insert the V5
screw in the dedicated hole F5. Insert the washer R5 and tighten the knob M23.
- Securing the base unit (fig.6): use 4 dowels with relative screws complete with
washers (material not supplied), inserted in the securing holes F6.
14.3 SECURING THE OPERATING HANDLE (FIG.7)
- Insert the screw V7 in the relative hole in the arm and secure it with the nut D7.
- Completely screw the operating handle I7 on the screw V7.
14 - Arm knob
16 - Operating handle
17 - Operating handle securing screw M6
18 - Operating handle securing nut M6
21 - 4 mm Allen wrench
22 - 5 mm Allen wrench
7