Mitsubishi Electric Mr.SLIM PLA-SM EA Serie Manual De Instrucciones página 10

3. Operation 3. Operation
■
Manual vane angle (Wired remote controller)
Main Main menu
Maintenance
Initial setting
Service
Main display:
Cursor Page
F1 F2 F3 F4
Maintenance menu
Auto descending panel
Manual vane angle
3D i-See sensor
Main menu:
Cursor
F1 F2 F3 F4
Manual vane angle
Ref. address
Unit No.
Identify unit Check button
Input display:
Cur. Address Check
F1 F2 F3 F4
Manual vane angle
Select:
Outlet Angle
F1 F2 F3 F4
Manual vane angle
Setting
F1 F2 F3 F4
Note:
Do not set the draft reduction in an environment with high humidity.
Otherwise, condensation may form and drip.
10
1 Select "Maintenance" from the
Main menu (refer to page 8), and
press the [SELECT] button.
2 Select "Manual vane angle" with
the [F1] or [F2] button, and press
the [SELECT] button.
3 Move the cursor to "Ref. address"
or "Unit No." with the [F1] button
to select.
Select the refrigerant address
and the unit number for the units
to whose vanes are to be fi xed,
with the [F2] or [F3] button, and
press the [SELECT] button.
• Ref. address: Refrigerant ad-
dress
• Unit No.: 1, 2, 3, 4
Press the [F4] button to confi rm
the unit.
The vane of only the target
indoor unit is pointing downward.
4 The current vane setting will ap-
pear.
Select the desired outlets from
1 through 4 with the [F1] or [F2]
button.
• Outlet: "1", "2", "3", "4" and "1, 2,
3, 4, (all outlets)"
Press the [F3] or [F4] button to
go through the option in the order
of "No setting (reset)", "Step 1",
"Step 2", "Step 3", "Step 4", "Step
5" and "Draft reduction*".
Select the desired setting.
* Draft reduction
The airfl ow direction for this set-
ting is more horizontal than the
airfl ow direction for the "Step 1"
setting in order to reduce a drafty
feeling. The draft reduction can
be set for only 1 vane.
■
Vane setting
No setting Step 1
Step 3 Step 4
Draft
All outlets
reduction*
Press the [SELECT] button to save the settings.
A screen will appear that indicates the setting information is being trans-
mitted.
The setting changes will be made to the selected outlet.
The screen will automatically return to the one shown above (step 5)
when the transmission is completed.
Make the settings for other outlets, following the same procedures.
If all outlets are selected,
the unit goes into operation.
Navigating through the screens
• To go back to the Main menu ................ [MENU] button
• To return to the previous screen .......... [RETURN] button
■
Manual vane angle (Wireless remote controller)
Fig. 1
Fig. 2
Fig. 3
Display
Setting Step 1
Display
Setting Step 5 No setting
* The draft reduction can be set for only 1 vane.
The setting is enabled only for the last vane that was set.
Step 2
Step 5
will be displayed the next time
1 Going to the Manual vane setting
mode
Press the button.
(Start this operation from the sta-
tus of remote controller display
turned off.)
"FUNCTION" is lighted and "1"
blinks. (Fig. 1)
Press the button to select "2",
and then press the
2 Selecting the vane number (Fig.
2)
Press the buttons to select
the vane number A, and then
A
press the button.
3 Setting the vane angle (Fig. 3)
Press the buttons to select
the vane angle B.
Point the wireless remote control-
B
ler toward the receiver on the
indoor unit, and then press the
button.
Step 2 Step 3 Step 4
No display
Draft reduction*
button.