Maintenance And Inspection - Hitachi SV 12V Instrucciones De Manejo

Ocultar thumbs Ver también para SV 12V:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
2. How to hold the orbital sander
While gripping the knob with one hand and the handle
with the other, lightly press the sander against the
surface to be sanded so that the sanding paper uniformly
contacts the surface, as shown in Fig. 6. DO NOT
apply excessive pressure to the sander while sanding.
Excessive-pressure may cause overload of the motor,
reduced service life of the sanding paper, and lowered
sanding or polishing effi ciency.
3. How to move the orbital sander
For optimum operating effi ciency, alternately move the
sander forward and backward at a constant speed and
balance.
4. Changing the rotating Speed (model SV12V only)
SV12V has an electronic control system which can be
use to set the rotating speed between 4000 and 10000
revolutions per minute.
As shown in Fig. 7, dial position "1" is for minimum speed
and position "5" for maximum speed.
MOUNTING THE OPTIONAL ACCESSORIES
1. Mounting the magic pad.
Loosen the six screws.
Remove the pad and attach the magic pad.
CAUTION
Replace the pad only. Use the other parts without
removing them.
2. Mounting the cleaner adapter (for models SV12V
and SV12SD) (Fig. 8).
After mounting the dust collector hose onto the cleaner
adapter, mount the cleaner adapter onto the unit in the
same way as mounting the dust bag.

MAINTENANCE AND INSPECTION

1. Empting and cleaning the Dust Bag (for models
SV12V and SV12SD)
If the dust bag contains too much saw dust, dust collection
will be aff ected. Empty the dust bag when it gets full.
Remove the dust bag, open the fastener, and dispose of
the contents.
2. Inspecting the sanding paper
Since use of worn-out sanding paper will degrade
effi ciency and cause possible damage to the pad,
replace the sanding paper as soon a excessive abrasion
is noted.
3. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
4. Inspecting the carbon brushes (Fig. 10)
The motor employs carbon brushes which are
consumable parts. Since an excessively worn carbon
brush can result in motor trouble, replace the carbon
brush with a new one having the same carbon brush No.
shown in the fi gure when it becomes worn to or near the
"wear limit". In addition, always keep carbon brushes
clean and ensure that they slide freely within the brush
holders.
5. Replacing carbon brushes
○ Disassembling
(1) Loosen the two screws on the top cover, and remove the
top cover. (Fig.11)
(2) Lift out the brush holder together with the carbon brush,
while being very careful not to forcibly pull the internal
wires within the brush holder.
(3) Remove the carbon brush from the brush holder.
5
○ Reassembling
(1) Insert the brush terminal into the brush holder. Turn the
brush terminal 90˚.
(2) While maintaining this brush terminal position as
explained in (1), insert the new carbon brush into the
brush holder.
(3) While pressing the carbon brush against the outside wall
of the housing's bearing compartment, insert the brush
holder into the housing's original position.
(4) Place the internal wire in the specifi ed position. Be
very careful not to allow the internal wire to contact the
armature or rotating parts of the motor. (Fig. 12)
(5) Replace the top cover, while being careful to ensure it
does not pinch the internal wire, and secure it fi rmly with
the two screws.
CAUTION
Should the internal wire be pinched by the top cover
or come in contact with the armature or rotating parts
of the motor, a serious danger of electric shock to the
operator will be created. Exercise extreme caution in
disassembling and reassembling the motor, following the
above procedure exactly.
DO NOT attempt disassemble any parts other than those
necessary to eff ect replacement of the carbon brush.
6. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
7. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modifi cation and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized Service
Center.
This Parts List will be helpful if presented with the tool to
the Hitachi Authorized Service Center when requesting
repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modifi ed to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE
Due to HITACHI's continuing program of research and
development, the specifi cations herein are subject to change
without prior notice.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Sv 12sdSv 12se

Tabla de contenido