Caution - Vortice MICROCOMFORT Manual De Instrucciones

Caution:

This symbol indicates precautions that must be taken to avoid damage to the appliance
• Do not make modifications of any kind to this
appliance.
• Take particular care if the appliance is used in
unsupervised environments.
• Do not expose this appliance to the weather (rain,
sun, etc.).
• Regularly inspect the appliance for visible
imperfections. If the appliance does not function
correctly, contact Vortice immediately.
• Should the appliance be dropped or suffer a heavy
blow, have it checked immediately by Vortice.
• If the appliance does not function correctly or
develops a fault, turn it off, disconnect the plug from
the power supply and contact Vortice immediately.
Ensure that only genuine original Vortice spares are
used for any repairs.
• Never position the appliance directly under a power
socket.
• The appliance must be properly connected to the
power supply in compliance with applicable
standards; it does not require to be earthed, as it is
double-insulated. If in doubt, request a qualified
electrician to perform a thorough check.
• The electrical power supply/socket to which the
appliance is to be connected must be able to provide
the maximum electrical power required by the
appliance.
• If the power socket is of a different type to the plug
fitted on the appliance, call a qualified technician and
ask him to replace it with a socket of the right type.
Do your best to avoid the use of adapters, multiple
sockets and/or extension leads;
if necessary, first make sure that they comply with
current safety regulations and check that the
maximum allowed power is compatible with the
values on the appliance's rating plate. Any extension
leads must be as short as possible to prevent them
from causing overheating and triggering the
appliance's thermal cut-out device.
• Do not pull on the power cable, do not place it near
heat sources and always uncoil it completely to
prevent dangerous overheating. If the cable or the
power plug are damaged, take the appliance to
Vortice for replacement.
• Do not cover, squeeze or place the power cable near
hot objects to avoid any risk of overheating or
damage; at the same time, make sure it is placed so
that it does not create an obstacle.
• Do not coil the power cable on the appliance and do
not operate the appliance with the cable coiled.
• To prevent hazardous overheating, it is
recommended to uncoil the power cable entirely and
use the appliance as indicated in the instructions.
• During operation, the power socket must be easily
accessible to enable quickly unplugging from the
mains.
• A limited increase in temperature in the power cable
and plug during use of the appliance is to be
considered normal; however, if the phenomenon
increases to the point that they become too hot to
touch or start to deform, contact Vortice immediately.
• Never place the power cable in front of the heating
element.
• Always keep the appliance in an upright position.
8
• When the appliance is not being used, turn it off and
disconnect the plug from the power supply.
• Before cleaning the appliance in any way, turn it off
and disconnect the plug from the power supply.
• Do not immerse the appliance in water.
• Do not insert anything into the appliance.
• Keep the appliance's intake and outlet grilles free and
uncovered.
• Do not cover the appliance, as this may result in
dangerous overheating.
• This appliance is not suited for rooms used in
zootechnics.
N.B. The appliance is equipped with safety devices
(reset manually) which cuts out if the appliance
itself starts to overheat, so as to avoid any risk of
damage. In these cases, disconnect the plug, leave
the appliance to cool for approximately 10 min. and
lastly plug it back into the power socket. To avoid
the harmful effects of continual switching on and
off, it is necessary to remove the cause of the
trouble (grilles obstructed, appliance tipped over,
fan jammed, etc).
For full compliance with European Regulation No.
2015/1188 EU, this product must be subjected to an
external control device that regulates heat emission in
the room where it is installed.
*(or an authorized Vortice dealer if you are outside the
UK-Ireland territory)
3
Specifications for the power supply must
correspond to the electrical data on the data plate.