Intended Use; Dga419 Dga469 Dga519 - Makita DGA419 Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Wheel diameter
Max. wheel thickness
Rated speed (n)
Overall length
Rated voltage
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

The tool is intended for grinding, sanding, wire brushing
and cutting of metal and stone materials without the use
of water.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745-2-3:
Model DGA419
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DGA469
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DGA519
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
) : 80 dB(A)
pA
) : 80 dB(A)
pA
) : 80 dB(A)
pA
DGA419
100 mm (4")
2.4 - 3.0 kg
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745-2-3:
Model DGA419
Work mode: surface grinding with normal side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: surface grinding with anti vibration side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DGA469
Work mode: surface grinding with normal side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: surface grinding with anti vibration side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
7 ENGLISH
DGA469 DGA519
115 mm (4-1/2") 125 mm (5")
6 mm
-1
8,500 min
396 mm
D.C. 18 V
2.5 - 3.1 kg
DC18SH
2
) : 4.5 m/s
h, AG
2
2
) : 6.0 m/s
h, AG
2
2
) : 5.0 m/s
h, AG
2
2
) : 5.5 m/s
h, AG
2