Before Use; Safety Instructions; Lamp (Re)Placement - JB Systems Light MIRROR BALL SET Manual De Instrucciones

ENGLISH
Thank you for buying this JB Systems product. To take full advantage of all possibilities and for your own
safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
• This device has been designed to produce decorative effect lighting and is used in light show systems.
• Complete set containing: mirror ball + mirror ball motor + pinspot + Par36 30W/6V lamp + Color disc with
motor.

BEFORE USE

• Before you start using this unit, please check if there's no transportation damage. Should there be any, do
not use the device and consult your dealer first.
• Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
• Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the carton contains the following items:
• Operating instructions
• Mirror ball
• Mirror ball motor
• Mirror ball chain
• Pinspot
• Par36 30W/6V lamp
• Color disc
• Color disc motor.

SAFETY INSTRUCTIONS:

• To protect the environment, please try to recycle the packing material as much as possible.
• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
• This unit is for indoor use only.
• Don't place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
• Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
• Don't cover any ventilation openings as this may result in overheating.
• Prevent use in dusty environments and clean the unit regularly.
• Keep the unit away from children.
• Inexperienced persons should not operate this device.
• Maximum save ambient temperature is 45°C. Don't use this unit at higher ambient temperatures.
• The units' surface temperature may reach up to 85°C. Don't touch the housing with bare hands during its
operation.
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
JB SYSTEMS®
OPERATION MANUAL
1/24 MIRROR BALL SET
ENGLISH
and servicing.
• Allow the device about 10 minutes to cool down before replacing the bulb or start servicing.
• Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing.
• The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
• Check that the available voltage is not higher than the one stated on the rear panel of the unit.
• The power cord should always be in perfect condition: switch the unit immediately off when the power cord
is squashed or damaged.
• Never let the power-cord come into contact with other cables!
• This fixture must be earthed to in order comply with safety regulations.
• Don't connect the unit to any dimmer pack.
• Always use an appropriate and certified safety cable when installing the unit.
• In order to prevent electric shock, do not open the cover. Apart from the lamp and mains fuse there are no
user serviceable parts inside.
• Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
• In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
• The housing and the lenses must be replaced if they are visibly damaged.
• Please use the original packing when the device is to be transported.
• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don't use the effect in the presence of persons suffering
from epilepsy.
DESCRIPTION:
1. Mirror ball eyelet
2. Mirror ball
3. Color disc
4. Color disc motor
5. PAR36 lamp + fixation ring
6. Pinspot projector
7. Mirror ball chain
8. Mirrror ball motor

LAMP (RE)PLACEMENT

In case of replacement of the lamp or maintenance, do not open the fixture within 10
minutes until the unit cools down after switching off. Always unplug the unit before
servicing! Always use the same type of spare parts (bulbs, fuses, etc.) When
replacing parts, please only genuine spare parts.
• Switch off the projector and unplug the mains cable.
• Wait for about 10 minutes until the projector has been cooled down.
• Remove the fixation ring in front of the lamp by pressing it together.
• Remove the old lamp from the projector and unscrew the wires to the lamp.
• Loosen the screws on the new 6V 30W Par 36 lamp.
• Connect the wires with the new lamp
• Tighten the screws using an appropriate screwdriver
• Insert the lamp in the housing.
• Fix the lamp with the fixation ring.
Attention! Never install lamps with a higher wattage! Lamps with higher wattage generate temperatures
the projector was not designed for. The lamp transformer will burn due to current overload.
JB SYSTEMS®
OPERATION MANUAL
2/24 MIRROR BALL SET