Overhead Rigging - JB Systems Light MIRROR BALL SET Manual De Instrucciones

ENGLISH
MOUNTING THE COLOR WHEEL
• Unscrew the nut and the first tooth ring from the fixation axis of the color disc motor.
• Remove the foil of the color disc.
• Slip the color disc onto the fixation axis of the color disc motor
• Slip the tooth ring first and then the nut onto the fixation axis.
• Fasten the nut without damaging the color disc.
• Fix the color wheel with motor via the fixation on the motor to the pinspot housing and tighten the screw.
MIRROR BALL MOTOR INSTALLATION INSTRUCTIONS
• The 3 fixation holes are located on the base plate.
• Hold the base plate onto the location where the device is to be installed.
• Mark the boreholes with a pen or a suitable tool.
• Drill the holes.
• Hold the base plate in the desired position and tighten it.
• Attach the mirror ball using the mirror ball chain

OVERHEAD RIGGING

• Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
• Locate the fixtures in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
• Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
• Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
• The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
• Don't cover any ventilation openings as this may result in overheating.
• The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
OPERATING INSTRUCTIONS
• Once connected to the mains the device starts running.
• Regular breaks during operation are essential to maximize the life of this device as it is not designed for
continual use.
• Do not switch the projector on and off in short time intervals as this reduces the lamp life.
• The projectors' surface temperature may reach up to 85°C. Don't touch the housing with bare-hands
during its operation.
• Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing.
• In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
• Important: Never look directly into the light source! Don't use the effect in the presence of persons
suffering from epilepsy.
JB SYSTEMS®
OPERATION MANUAL
3/24 MIRROR BALL SET
ENGLISH
MAINTENANCE
• Make sure the area below the installation place is free from unwanted persons during servicing.
• Unplug the mains cable .
During inspection the following points should be checked:
• All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
• Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
• The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
SPECIFICATIONS
MIRROR BALL MOTOR:
Mains Input: AC 230V, 50Hz
Power consumption: 4W
Maximum load: 3kg (chains + Mirror ball)
Rotation Speed: 1.5RPM
Size: 11 x 11 x 5cm
Weight: 0.3kg
COLOR DISC + MOTOR:
Mains Input: AC 230V, 50Hz
Rotation Speed: 2.5RPM
Disc colors: Red, green, yellow, blue
Disc diameter: 23cm
PINSPOT:
Mains Input: AC 230V, 50Hz
Power consumption: 36W
Lamp: PAR36 max. 6V 30W (4515)
Size: 15 x 12 x 12cm
Weight: 1kg
Every information is subject to change without prior notice
JB SYSTEMS®
OPERATION MANUAL
4/24 MIRROR BALL SET