Tabla De Contenido; Important Safety Information; Safety - Titan CAPSPRAY HVLP Manual Del Propietário

Important Safety Information

This symbol indicates a hazardous situation, which, if not
not avoided could result in death or serious injury.
To reduce the risks of fire or explosion, electrical shock
and the injury to persons, read and understand all
instructions included in this manual. Be familiar with the
controls and proper usage of the equipment.
haZaRD: EXPLOSION haZaRD DuE TO
INcOMPaTIBLE MaTERIaLS
Will cause property damage or severe injury.
PREvENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such as bleach,
mildewcide, methylene chloride and 1,1,1 - trichloroethane. They
are not compatible with aluminum.
• Contact your coating supplier about the compatibility of material
with aluminum.
haZaRD: GENERaL
Can cause severe injury or property damage.
PREvENTION:
• Read all instructions and safety precautions before operating any
equipment.
• Follow all appropriate local, state, and national codes governing
ventilation, fire prevention, and operation.
• The United States Government Safety Standards have been
adopted under the Occupational Safety and Health Act (OSHA).
These standards, particularly Part 1910 of the General Standards
and Part 1926 of the Construction Standard should be consulted.
• Use only manufacturer authorized parts. User assumes all risks
and liabilities when using parts that do not meet the minimum
specifications and safety devices of the manufacturer.
• Before each use, check all hoses for cuts, leaks, abrasion or
bulging of cover. Check for damage or movement of couplings.
Immediately replace the hose if any of these conditions exist.
Never repair a hose. Replace it with an identical replacement hose.
• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
• Never aim the spray gun at any part of the body.
haZaRD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite. Property
damage and/or severe injury can occur.
PREvENTION:
• Exhaust and fresh air introduction must be provided
to keep the air within the spray area free from
accumulation of flammable vapors.
• Turbine contains sparking parts. Turbine must
be placed in a well ventilated area at maximum
distance from the spray area.
• Avoid all ignition sources such as static electricity, open flames,
pilot lights, hot objects, cigarettes, and sparks from connecting
and disconnecting power cords and working light switches.
• Use extreme caution when using materials with a flashpoint below
70° F (21°C). A fluid's flashpoint is the temperature at which
vapors from the fluid could ignite if exposed to a flame or spark.
• Fire extinguishing equipment must be present and in working
order.
• The power cord must be connected to a grounded circuit.
• Follow the material and solvent manufacturer's safety precautions
and warnings.
English
operating the equipment. SavE ThESE INSTRucTIONS.
·
Read all safety information before
haZaRD: haZaRDOuS vaPORS
Paints, solvents, insecticides, and other materials can be harmful if
inhaled or come in contact with the body. Vapors can cause severe
nausea, fainting, or poisoning.
PREvENTION:
• Use a respirator or mask if vapors can be inhaled.
Read all instructions supplied with the mask to be
sure it will provide the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating manufacturer.
haZaRD: ELEcTRIc ShOck haZaRD
May cause severe injury.
PREvENTION:
• Never immerse electric parts in water or any other liquid. Wipe
the exterior of the pump with a damp cloth for cleaning. Always
make sure the pump is disconnected from the turbine before
taking it apart for cleaning and/or service.
Service
Should your spray system need service during the warranty period,
return your unit and the proof of purchase to the distributor where it was
purchased. At our option, the unit will be repaired or replaced. In a
continued commitment to improve quality, we reserve the right to make
component or design changes when necessary.
IMPORTaNT: Never operate unit for more than ten seconds without
fluid. Operating this unit without fluid will cause unnecessary wear
to the seal.
Table of contents
Safety ......................................................................................... 2
Specifications ........................................................................... 3
Introduction ............................................................................... 3
Transfer Pump Controls ...................................................... 3
Setup .......................................................................................... 4
Converting the Gun to Pressure Feed................................. 4
Mounting the Transfer Pump ............................................... 4
Connecting the Material Hose ............................................. 5
Hose Configurations ............................................................ 5
Operation ................................................................................... 6
Material Thinning ................................................................. 6
Preparing a New Sprayer .................................................... 6
Preparing to Paint................................................................ 6
Painting ..................................................................................... 6
cleanup ..................................................................................... 7
Cleaning the Inlet / Outlet Valves ........................................ 7
Maintenance .............................................................................. 8
General Repair and Service Notes...................................... 8
Service ....................................................................................... 8
Replacing the Inlet Valve..................................................... 8
Replacing the Outlet Valve .................................................. 9
Replacing the Seal and Piston ............................................ 9
Replacing the Pressure Setting Valve ............................... 10
Replacing the Motor .......................................................... 11
Troubleshooting ..................................................................... 12
Parts List ............................................................................ 38-40
Electrical Schematic .......................................................... 41
Warranty .................................................................................. 44
2 © Titan Tool. All rights reserved.