General Power Tool Safety Warnings - Makita PH01 Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Capacities
No load speed (RPM)
Blows per minute
Overall length
Rated voltage
Standard battery cartridges
• Due to our continuing programme of research and development, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

General Power Tool Safety Warnings

WARNING Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered or
1.
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while
3.
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
Power tool plugs must match the outlet. Never modify
4.
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
Model
Masonry
Steel
Wood
Wood screw
Machine screw
High (2)
Low (1)
High (2)
Low (1)
Net weight
PH01
10 mm (3/8")
10 mm (3/8")
25 mm (1")
5.1 mm x 63 mm
(13/64" x 2-1/2")
216 mm (8-1/2")
1.5 kg (3.3lbs)
D.C. 14.4 V
BL1411G / BL1413G /
BL1415G
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
When operating a power tool outdoors, use an
8.
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is
9.
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of an GFCI
reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or med-
ication. A moment of inattention while operating
power tools may result in serious personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
2 ENGLISH
PH02
13 mm (1/2")
13 mm (1/2")
36 mm (1-7/16")
6 mm x 75 mm (1/4" x 2-15/16")
6 mm (1/4")
0- 1,400 /min
0 - 400 /min
0 - 21,000
0 - 6,000
246 mm (9-11/16")
1.7 kg (3.8lbs)
D.C. 18 V
BL1811G / BL1813G /
BL1815G