Emerson ROC800 Serie Instrucciones Para Un Uso Seguro página 4

Safe Use Instructions – ROC800-Series
Specifications
POWER
12 V dc Power Input Module:
Operating Range: 11.25 to 16 V dc.
Input Current: 5 Amps maximum
24 V dc Power Input Module:
Operating Range: 20 to 30 V dc.
Input Current: 2 Amp maximum
30 V dc Power Input Module:
Operating Range: 11 to 30 V dc.
Input Current: 7 Amp maximum
MATERIALS
Case: Acrylonitrile Butadiene Styrene (ABS) Plastic.
Wire Channel Covers: Polypropylene Plastic.
Modules: Thermoplastic Polyester, solvent-resistant.
ENVIRONMENTAL
Operating Temp.: -40 to +75°C.
Storage Temp.: -40 to +85°C.
Relative Humidity: IEC68-2-3; 5-95% non-condensing.
WEIGHT
1.65 kg for housing, backplane and CPU.
I/O Modules: Vary from 49–60 g.
Modem Module: 113.4 g.
EIA-232 (RS-232) Module: 47.6 g.
EIA-422/485 (RS-422/485) Module: 49.9 g.
MVS Module: 61.2 g.
12 V dc Power Input Module: 97.5 g.
24 V dc Power Input Module: 120 g.
30 V dc Power Input Module: 91 g.
APPROVALS
Evaluated to the following European Standards (EMC):
EN55011 (Emissions).
EN61000-4-2 (Electrostatic Discharge Immunity).
EN61000-4-3 (Electromagnetic Field Immunity).
EN61000-4-4 (Electrical Fast Transients Immunity).
EN61000-4-5 (Surge Immunity).
EN61000-4-6 (Conducted Immunity).
Evaluated to the following European Standards (ATEX):
EN60079-0:2012.
EN60079-15:2010.
Certified by Sira as Model W40135.
Evaluated to the following Standards (IEC):
IEC 60079-0:2011 (6 th Edition)
IEC 60079-15:2010, 4 th
Product Markings for Hazardous Locations:
Ex nA IICT4 Gc (–40°C ≤ T
II 3 G.
Cert. No. Sira 05ATEX4046X
Edition
≤ +75°C),
amb
1. You receive the ROC800 in a box. Remove it from the
box.
2. Find a suitable location for the ROC800. Always install
the ROC800 in a user-supplied enclosure, as the ROC800
requires protection from direct exposure to rain, snow,
ice, blowing dust or debris, and corrosive atmospheres. If
the ROC800 is installed outside a building, it must be
placed in an IP54 (or better) rated enclosure.
Note: If you place the ROC800 inside an enclosure, use the
provided extension cable to locate the antenna
outside the enclosure. Seal any holes you make in
the enclosure for this purpose to ensure
maintenance of the required IP54 rating.
When choosing an enclosure, be sure to check all
clearances. Provide adequate clearance for wiring and
service. See Figure 2 and Figure 3.
ROC809SD.DSF
Figure 2. Side View of the ROC809
9.60 in.
(244 mm)
ROC809BT.DSF
Figure 3. Bottom View of the ROC809
3. The ROC800 housing mounts on two 35 x 7.5 mm DIN
rails. See Figure 4.
Part D301201X012
Page 2
9.51 in.
(242 mm)
7.50 in.
(191 mm)