Franklin Electric Little Giant 10EN-CIA-SFS Manual De Uso

Franklin Electric Co., Inc.
Oklahoma City, OK 73157-2010
www.LittleGiantPump.com
E N G L I S H
customerservice@lgpc.com
ENGLISH
EN
This instruction sheet provides you with the information required
to safely own and operate your product. Retain these instructions
for future reference.
The product you have purchased is of the highest quality
workmanship and material, and has been engineered to give you
long and reliable service. This product has been carefully tested,
inspected, and packaged to ensure safe delivery and operation.
Please examine your item(s) carefully to ensure that no damage
occurred during shipment. If damage has occurred, please
contact the place of purchase. They will assist you in replacement
or repair, if required.
READ THESE INSTRUCTIONS
ATTEMPTING TO INSTALL,
YOUR PRODUCT. KNOW THE PRODUCT'S APPLICATION,
LIMITATIONS, AND POTENTIAL
YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
AND/OR PROPERTY DAMAGE!
DESCRIPTION
This is a submersible effluent pump for use in basins or lift
stations, and is suitable for pumping sewage, effluent, wastewater,
and other non-explosive, non-corrosive liquids with up to 1/2"
spherical solids.
SAFETY GUIDELINES
1. Make certain pump is disconnected from power source before
attempting to service or remove any component.
2. Do not use to pump flammable or explosive fluids such as
gasoline, fuel oil, kerosene, etc. DO NOT use in explosive
atmospheres or hazardous locations as classified by NEC,
ANSI/NFPAT. Pump should be used with liquids compatible
with pump component materials.
3. Do not handle the pump with wet hands or when standing on
a wet or damp surface or in water.
4. Do not pull the pump out of the water by the power cord when
the pump is operating or connected to power source.
5. This pump is supplied with a grounding conductor and/or
grounding type attachment plug. To reduce the risk of electrical
shock, be certain that it is connected to a properly grounded
grounding type receptacle.
6. The National Electric Code requires a ground fault circuit
interrupter (GFCI) be installed in the branch circuit supplying
fountain equipment, pools, etc.
7. In any installation where property damage and/or personal
injury might result from an inoperative or leaking pump due to
power outages, discharge line blockage, or any other reason,
a backup system(s) and/or alarm should be used.
8. Support pump and piping when assembling and when installed.
Failure to do so may cause piping to break, pump to fail,
motor bearing failures, etc.
10EN-CIA-SFS
10EN-CIA-RF
10EN-CIM
10EN-CBM
10EN-CBA
CAREFULLY BEFORE
OPERATE, OR SERVICE
HAZARDS. PROTECT
TO COMPLY WITH THESE
Figure 1 - Typical insTallaTion • insTallaTion Type •
INSTALACION TIPICA (10EN-CIA-SFS SHOWN)
9. This pump's motor housing is filled with a dielectric oil for
motor heat transfer and lifetime lubrication of the bearings.
This oil is non-toxic to aquatic life. However, suffocation can
occur if oil is left on the water surface. If oil escapes the motor
housing it can be removed from the surface quickly by placing
newspapers on the water surface to soak up the oil.
10. The pump motor is equipped with an automatic resetting thermal
protector and may restart unexpectedly. Protector tripping is
an indication of motor overloading as a result of excessively high
or low voltage, inadequate wiring, incorrect motor connections,
or a defective motor or pump.
ELECTRICAL CONNECTIONS
1. Check the pump label for proper voltage required. Do not
connect to voltage other than that shown.
2. If pump is supplied with a 3-prong electrical plug, the third
prong is to ground the pump to prevent possible electrical
shock hazard. DO NOT REMOVE the third prong from the
plug. A separate branch circuit is recommended.
Do not use an extension cord. Do not cut plug from the cord.
If the plug is cut or the cord is shortened, then this action will
void the warranty.
3. If the cord is equipped with stripped lead wires, such as on
230V models, be sure that the lead wires are connected to a
power source correctly. The green/yellow wire is the ground.
The blue (or white) and brown (or black) are live.
1