Makita DTW700 Manual De Instrucciones página 7

Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
Fig.2: 1. Indicator lamps 2. Check button
3UHVV WKH FKHFN EXWWRQ RQ WKH EDWWHU\ FDUWULGJH WR LQGL-
FDWH WKH UHPDLQLQJ EDWWHU\ FDSDFLW\ 7KH LQGLFDWRU ODPSV
light up for a few seconds.
Indicator lamps
Lighted 2
NOTE: Depending on the conditions of use and the
DPELHQW WHPSHUDWXUH WKH LQGLFDWLRQ PD\ GL HU VOLJKWO\
IURP WKH DFWXDO FDSDFLW\
Switch action
Fig.3: 1. Switch trigger
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
7R VWDUW WKH WRRO VLPSO\ SXOO WKH VZLWFK WULJJHU 7RRO
VSHHG LV LQFUHDVHG E\ LQFUHDVLQJ SUHVVXUH RQ WKH VZLWFK
trigger. Release the switch trigger to stop.
NOTE: 7KH WRRO DXWRPDWLFDOO\ VWRSV ZKHQ \RX NHHS
pulling the switch trigger for 6 minutes.
NOTE: When full speed mode is turned on, the rota-
WLRQ VSHHG EHFRPHV IDVWHVW HYHQ LI \RX GR QRW SXOO WKH
VZLWFK WULJJHU IXOO\
For detail information, refer to the section of full speed
mode.
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
EDWWHU\
7KH EDWWHU\
PD\ KDYH
malfunctioned.
7 ENGLISH
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Fig.4: 1. Lamp
Fig.5: 1. Button
To turn on the lamp status, press the button
RQH VHFRQG 7R WXUQ R WKH ODPS VWDWXV SUHVV WKH EXW-
ton for one second again.
With the lamp status ON, pull the switch trigger to turn
RQ WKH ODPS 7R WXUQ R  UHOHDVH LW 7KH ODPS JRHV RXW
DSSUR[LPDWHO\  VHFRQGV DIWHU UHOHDVLQJ WKH VZLWFK
trigger.
With the lamp status OFF, the lamp does not turn on
even if pulling the trigger.
NOTE: 7R FRQ¿UP WKH ODPS VWDWXV SXOO WKH WULJJHU
:KHQ WKH ODPS OLJKWV XS E\ SXOOLQJ WKH VZLWFK WULJJHU
the lamp status is ON. When the lamp does not come
on, the lamp status is OFF.
NOTE: :KHQ WKH WRRO LV RYHUKHDWHG WKH OLJKW ÀDVKHV
IRU RQH PLQXWH DQG WKHQ WKH /(' GLVSOD\ JRHV R  ,Q
this case, cool down the tool before operating again.
NOTE: 8VH D GU\ FORWK WR ZLSH WKH GLUW R WKH OHQV RI
the lamp. Be careful not to scratch the lens of lamp, or
LW PD\ ORZHU WKH LOOXPLQDWLRQ
NOTE: While pulling the switch trigger, the lamp
status cannot be changed.
NOTE: )RU DSSUR[LPDWHO\  VHFRQGV DIWHU UHOHDVLQJ
the switch trigger, the lamp status can be changed.
Reversing switch action
Fig.6: 1. Reversing switch lever
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the
GLUHFWLRQ RI URWDWLRQ EHIRUH WKH WRRO VWRSV PD\ GDP-
age the tool.
CAUTION:
When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
for